Liste des tests | Services Techniques
Le Groupe CTT est un centre de transfert de technologie spécialisé en recherche, développement et analyses des textiles techniques, des géosynthétiques et des matériaux avancés à base de textile.
| Nom de l’analyse | Description |
|---|---|
| 16CFR 1500.49 | Technical requirements for determining a sharp metal or glass edge in toys and other articles intended for use by children under 8 years of age. |
| 16CFR 1500.53 E TORQ | Torque Test |
| 16CFR 1500.53 F TENS | Tension Test |
| 16CFR 1610 | Standard for the Flammability of Clothing Textiles |
| 16CFR 1615 | Flammability of Children’s Sleepwear: Sizes 0 through 6X (FF 3-71) Garment |
| 16CFR 1616 | Flammability of Children’s Sleepwear: Sizes 7 through 14 (FF 5-74) Fabric |
| 16CFR 1630 | Standard for the Surface Flammability of Carpets and Rugs (FF 1-70) |
| 16CFR 1632 | Standard for the Flammability of Mattresses and Mattress Pads – Section 1632.6 |
| 42CFR 84.180 | Airflow resistance |
| 49CFR FMVSS 302 | Federal Motor Vehicle Safety Standards (FMVSS) Section 571.302 – Flammability of interior materials |
| 5100-187 BACTERIA | Bacteria Resistance Test |
| 5100-187 COLD RESIST | Cold Temperature Resistance |
| 5100-187 COMPRESSION | Flexibility and Compressibility Test |
| 5100-187 FUNGI RESIS | Fungi Resistance Test |
| 5100-187 MILDEW TEST | Jacket Mildew Resistance Test |
| 5100-187 OZON RESIST | Lining Resistance to Ozone |
| 5100-187 TENSILE | Tensile Strength and Elongation of Lining |
| 5100-187 TENSILE | Tensile Strength and Elongation of Lining – After Oven Aging |
| 5100-187 WATER IMMER | Lining Resistance to Water Immersion |
| A A 55245 BREAKING | Breaking strength – Necklace, Personnel, Identification tag |
| AAMA 2605 ADHESION | Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels – Flim Adhesion |
| AAMA 2605 IMPACT | Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels – Impact Resistance |
| AAMA 711 AGING | Accelerated Aging with Ultraviolet Light Exposure |
| AAMA 711 AGING | Elevated Temperature Exposure |
| AAMA 711 AGING | Thermal Cycling |
| AAMA 711 AGING | Adhesion of Self Adhering Flashing after Water Immersion |
| AAMA 711 BENDING | Cold Temperature Pliability |
| AAMA 711 NAIL-SEAL | Water Penetration Resistance Around Nails |
| AAMA 711 PEEL | Peel Adhesion |
| AAMA 711 SELF-PEEL | Peeling Resistance |
| AAMA 711 TENSILE | Tensile Strength |
| AASHTO T341 | Determination of Compression Capacity for Profile Wall Plastic Pipe by Stub Compression Loading |
| AATCC 100 | Antibacterial Finishes on Textile Materials: Assessment of |
| AATCC 104 | Colorfastness to Water Spotting |
| AATCC 110 | Whiteness of Textiles |
| AATCC 112 | Formaldehyde Release from Fabric: Sealed Jar Method |
| AATCC 115 | Electrostatic Clinging of Fabrics: Fabric-to-Metal |
| AATCC 116 | Colorfastness to Crocking: Rotary Vertical Crockmeter |
| AATCC 117 | Colorfastness to Heat: Dry (Excluding Pressing) |
| AATCC 118 | Oil Repellency: Hydrocarbon Resistance |
| AATCC 119 | Colorfastness to Flat Abrasion (Frosting): Screen Wire |
| AATCC 120 | Colorfastness to Flat Abrasion (Frosting): Emery |
| AATCC 124 | Smoothness Appearance of Fabrics after Repeated Home Laundering |
| AATCC 125 | Colorfastness to Perspiration and Light |
| AATCC 127 | Acceptance Criteria for Water-Resistive Barriers – Water Resistance: Hydrostatic Pressure |
| AATCC 128 | Wrinkle Recovery of Fabrics: Appearance |
| AATCC 130 | Soil Release: Oily Stain Release |
| AATCC 132 | Colorfastness to Drycleaning |
| AATCC 133 | Colorfastness to Heat: Hot Pressing |
| AATCC 135 | Dimensional Changes of Fabrics after Home Laundering |
| AATCC 147 | Antibacterial Activity of Textile Materials: Parallel Streak |
| AATCC 15 | Colorfastness to Perspiration |
| AATCC 150 | Dimensional Changes of Garments after Home Laundering |
| AATCC 158 | Dimensional Changes on Drycleaning in Perchloroethylene: Machine Method |
| AATCC 16.3 | Colorfastness to Light: Xenon-Arc (Option 3) |
| AATCC 163 | Colorfastness to Storage: Dye Transfer |
| AATCC 169 | Weather Resistance of Textiles: Xenon Lamp Exposure (Option 1) |
| AATCC 179 | Skew Change in Fabrics After Home Laundering |
| AATCC 183 | Transmittance or Blocking of Erythemally Weighted Ultraviolet Radiation Through Fabrics |
| AATCC 188 | Colorfastness to Sodium Hypochlorite Bleach in Home Laundering |
| AATCC 193 | Aqueous Liquid Repellency: Water/Alcohol Solution Resistance Test |
| AATCC 195 | Liquid Moisture Management Properties of Textile Fabrics |
| AATCC 197 | Vertical Wicking of Textiles |
| AATCC 199 | Drying Time of Textiles: Moisture Analyzer |
| AATCC 20 | Fiber Analysis: Qualitative |
| AATCC 207 | Seam Twist in Garments Before and After Home Laundering |
| AATCC 20A NONFIBROUS | Nonfibrous Material – Clean Fiber Content |
| AATCC 212 | Fiber Fragment Release During Home Laundering |
| AATCC 22 | Water Repellency: Spray |
| AATCC 23 | Colorfastness to Burnt Gas Fumes |
| AATCC 3 | Colorfastness to Bleaching with Chlorine |
| AATCC 35 | Water Resistance: Rain Test |
| AATCC 42 | Water Resistance: Impact Penetration |
| AATCC 6 | Colorfastness to Acids and Alkalis |
| AATCC 61 | Colorfastness to Laundering: Accelerated |
| AATCC 66 | Wrinkle Recovery of Woven Fabrics: Recovery Angle – Option 2 |
| AATCC 70 | Water Repellency: Tumble Jar Dynamic Absorption Test |
| AATCC 76 | Electrical Surface Resistivity of Fabrics |
| AATCC 79 | Absorbency of Textiles |
| AATCC 8 | Colorfastness to Crocking: AATCC Crockmeter |
| AATCC 81 | pH of the Water-Extract from Wet Processed Textiles |
| AATCC 88B | Smoothness of Seams in Fabrics after Repeated Home Laundering |
| AATCC 88C | Crease Retention in Fabrics after Home Laundering |
| AATCC 92 | Test Method for Chlorine, Retained, Tensile Loss: Single Sample |
| AATCC 94 | Finishes in Textiles: Identification |
| AATCC EP1 | Evaluation Procedure for Gray Scale for Color Change |
| AATCC EVAL PROC 9 | Visual Assessment of Color Difference of Textiles |
| AATCC TS 006 | Procedure for Hand Laundering |
| ANSI 105 CHEM DEGRAD | Chemical Degradation Resistance |
| ANSI A100.1 4.1 | Allowable Lead Content |
| ANSI A100.1 4.4 | Operating Cord Length |
| ANSI A100.1 4.6 | Cord Cleats |
| ANSI A100.1 5.1-5.3 | Labeling and Operational Tag |
| AROMATIC HYDR RESIST | Resistance to Aromatic Hydrocarbon Fluid |
| ASHRAE 74 | Solar-Optical Properties of Materials |
| AS-NZS 1906.4 | Daylight colour and Luminance factor tests – Fluorescent colour |
| ASTM B117 | Standard Practice for Operating Salt Spray (Fog) Apparatus |
| ASTM B571 SCRIBE | Standard Practice for Qualitative Adhesion Testing of Metallic Coatings |
| ASTM C1028 | Static Coefficient of Friction of Ceramic Tile by the Horizontal Dynamometer Pull-Meter Method |
| ASTM C1104 | Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation |
| ASTM C1166 | Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories |
| ASTM C1258 | Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation |
| ASTM C1263 | Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C1305 | Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane |
| ASTM C1338 | Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C1353 | Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform, Double-Head Abraser |
| ASTM C1353 | Geosynthetic Cementitious Composite Mats and Barriers – Abrasion Resistance (ASTM C1353/C1353M) |
| ASTM C140 ABSORPTION | Standard Test Method for Sampling and Testing Concrete Masonry Units and Related Units – Absorption |
| ASTM C140 COMP | Standard Test Method for Sampling and Testing Concrete Masonry Units and Related Units – Compressive Strength |
| ASTM C165 | Measuring Compressive Properties of Thermal Insulations |
| ASTM C165 | Compressive Strength (ASTM C165) |
| ASTM C1803 | Abrasion Resistance of Mortar Surfaces Using a Rotary Platform Abraser |
| ASTM C203 | Breaking Load and Flexural Properties of Block-Type Thermal Insulation |
| ASTM C209 DIMENSIONS | Thickness and Size of Finished Board |
| ASTM C209 DIMENSIONS | Dimensions and Tolerances (ASTM C209 § 7 and 8) |
| ASTM C209 TENS-PARA | Cellulosic Fiber Insulating Board – Tensile Strength Parallel to Surface |
| ASTM C209 TENS-PARA | Tensile Strength (ASTM C209 § 12) |
| ASTM C209 TENS-PERP | Cellulosic Fiber Insulating Board – Tensile Strength Perpendicular to Surface |
| ASTM C209 TENS-PERP | Adhesion (ASTM C209 § 13) |
| ASTM C209 TRAN-STREN | Cellulosic Fiber Insulating Board – Transverse Strength |
| ASTM C209 TRAN-STREN | Transverse Load at Rupture (ASTM C209 § 10) |
| ASTM C209 WATER-ABS | Cellulosic Fiber Insulating Board – Water Absorption |
| ASTM C209 WATER-ABS | Water Absorption (ASTM C209 § 14) |
| ASTM C22 | Standard Specification for Gypsum |
| ASTM C273 | Shear Properties of Sandwich Core Materials |
| ASTM C297 | Flatwise Tensile Strength of Sandwich Constructions |
| ASTM C364 | Edgewise Compressive Strength of Sandwich Constructions |
| ASTM C393 | Core Shear Properties of Sandwich Constructions by Beam Flexure |
| ASTM C426 | Standard Test Method for Linear Drying Shrinkage of Concrete Masonry Units |
| ASTM C473 FLEX | Standard Test Methods for Physical Testing of Gypsum Panel Products – Flexural strength |
| ASTM C473 NAIL | Standard Test Methods for Physical Testing of Gypsum Panel Products – Nail pull resistance |
| ASTM C501 | Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser |
| ASTM C501 | Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser |
| ASTM C518 | Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
| ASTM C518 | Thermal Resistance (ASTM C518) |
| ASTM C550 | Standard Test Method for Measuring Trueness and Squareness of Rigid Block and Board Thermal Insulation |
| ASTM C550 | Offset (ASTM C550) |
| ASTM C550 | Straightedge (ASTM C550) |
| ASTM C550 | Vented Edge (ASTM C550) |
| ASTM C579 | Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C627 | Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester |
| ASTM C661 | Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer |
| ASTM C78 | Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) |
| ASTM C794 | Adhesion-in-Peel of Elastomeric Joint Sealants |
| ASTM C880 | Standard Test Method for Flexural Strength of Dimension Stone. |
| ASTM C99 | Modulus of Rupture of Dimension Stone |
| ASTM D1000 ADHESION | Pressure-Sensitive Adhesive-Coated Tapes used for Electrical/Electronic App.-Adhesion to Steel Panel |
| ASTM D1000 BREAKING | Breaking Strength and Elongation |
| ASTM D1000 FLAGGING | Flagging test |
| ASTM D1000 LENGTH | Length of Tape in a Roll |
| ASTM D1000 THICKNESS | Thickness |
| ASTM D1000 WIDTH | Width of Tape |
| ASTM D1002 | Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by tension loading |
| ASTM D1003 | Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D1004 | Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D1037 ABS-SWELL | Evaluating Properties of Wood-Base Fiber and .. Materials – Water Absorption and Thickness Swelling |
| ASTM D1037 BENDING | Evaluating Properties of Wood-Base Fiber and Particle Panel Materials – Static Bending |
| ASTM D1037 LINE-EXP | Evaluating Properties of Wood-Base Fiber and .. Materials-Linear Expansion with Change in Moisture |
| ASTM D1037 LINE-EXP | Linear Moisture Expansion (ASTM D1037 § 24) |
| ASTM D1042 | Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture |
| ASTM D1044 | Resistance of Transparent Plastics to Surface Abrasion by the Taber Abraser |
| ASTM D1052 | Measuring Rubber Deterioration – Cut Growth Using Ross Flexing Apparatus |
| ASTM D1059 | Yarn Number Based on Short-Length Specimens |
| ASTM D1117 | Standard Guide for Evaluating Nonwoven Fabrics -Trapezoid Tearing Strength |
| ASTM D1141 | Preparation of Substitute Ocean Water |
| ASTM D1203 | Volatile Loss from Plastics Using Activated Carbon Methods |
| ASTM D1204 | Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D1230 | Flammability of Apparel Textiles |
| ASTM D1238 | Melt Flow Rates of Thermoplastics by Extrusion Plastomer |
| ASTM D1239 | Resistance of Plastic Films to Extraction by Chemicals |
| ASTM D1243 | Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers |
| ASTM D1335 | Tuft Bind of Pile Yarn Floor Coverings |
| ASTM D1388 | Stiffness of Fabrics |
| ASTM D1422 | Twist in Single Spun Yarns by the Untwist-Retwist Method |
| ASTM D1423 | Twist in Yarns by Direct-Counting |
| ASTM D1424 | Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus |
| ASTM D1424 | Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus |
| ASTM D146 DIMENSIONS | Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing – Appearance and Dimensions of Rolls |
| ASTM D146 HEAT-LOSS | Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing – Loss on Heating |
| ASTM D146 HEAT-LOSS | Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing – Loss on Heating |
| ASTM D146 PLIABILITY | Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing – Pliability |
| ASTM D146 PLIABILITY | Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing – Pliability |
| ASTM D146 PLIABILITY | Asphalt-Saturated Organic Roofing Felt – Pliability |
| ASTM D146 STRENGTH | Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing – Strength |
| ASTM D146 STRENGTH | Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing – Breaking Strength |
| ASTM D1518 OPTION1 | Thermal Resistance of Batting Systems Using a Hot Plate |
| ASTM D1525 | Standard Test Method for Vicat Softening Temperature of Plastics |
| ASTM D1593 | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting – Thickness |
| ASTM D1596 | Dynamic Shock Cushioning Characteristics of Packaging Material |
| ASTM D1603 | Carbon Black Content in Olefin Plastics |
| ASTM D1621 | Compressive Properties of Rigid Cellular Plastics |
| ASTM D1623 | Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
| ASTM D1653 | Water Vapor Transmission of Organic Coating Films |
| ASTM D1682 | Breaking Load and Elongation of Textile Fabrics |
| ASTM D1683 | Failure in Sewn Seams of Woven Fabrics – Seam Efficiency |
| ASTM D1683 | Failure in Sewn Seams of Woven Fabrics – Seam Slippage |
| ASTM D1693 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D1693 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D1693 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D1693 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D1709 | Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D1709 | Resistance to Puncture of New Material |
| ASTM D1746 | Transparency of Plastic Sheeting |
| ASTM D1777 | Standard Test Method for Thickness of Textile Materials |
| ASTM D1777 | Thickness of Textile Materials |
| ASTM D1781 | Climbing Drum Peel for Adhesives |
| ASTM D1790 | Brittleness Temperature of Plastic Sheeting by Impact |
| ASTM D1813 | Measuring Thickness of Leather Test Specimens |
| ASTM D1815 | Water Absorption (Static) of Vegetable Tanned Leather |
| ASTM D1876 | Peel Resistance of Adhesives (T-Peel Test) |
| ASTM D1894 | Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D1907 | Linear Density of Yarn (Yarn Number) by the Skein Method |
| ASTM D1922 | Tear Resistance (ASTM D1922) |
| ASTM D1922 | Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing – Tear Strength |
| ASTM D1922 | Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D1970 ADHESION | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials… – Adhesion to Plywood |
| ASTM D1970 FLEX | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials… – Low Temperature Flexibility |
| ASTM D1970 LAPSEAM | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials… – Lap Integrity |
| ASTM D1970 NAIL | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials… – Capability to Seal Around Nail |
| ASTM D1970 TEAR | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials…- Tear Resistance |
| ASTM D1970 TENSILE | Spec. for Self-Adhering Polymer Mod. Bituminous Sheet Materials… – Max. Load and Elong. at Break |
| ASTM D1970 THERMSTAB | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials… – Thermal Stability |
| ASTM D1970 THICKNESS | Spec. for Self-Adhering Polymer Modified Bituminous Sheet Materials… – Thickness |
| ASTM D204 STRENGTH | Sewing Threads – Strength and Elongation |
| ASTM D204 TWIST | Sewing Threads – Twist |
| ASTM D2051 | Durability of Finish of Zippers to Laundering |
| ASTM D2058 | Durability of Finish of Zippers to Drycleaning |
| ASTM D2061-14.1 | Strength Tests for Zippers – Chain Crosswise Strength |
| ASTM D2061-14.2 | Strength Tests for Zippers – Element Pull-Off Strength |
| ASTM D2061-14.3 | Strength Tests for Zippers – Element Slippage Strength, Lengthwise |
| ASTM D2061-22.2 | Strength Tests for Zippers – Top Stop Holding Strength |
| ASTM D2061-22.3 | Strength Tests for Zippers – Bottom Stop Holding Strength, Slider |
| ASTM D2061-22.4 | Strength Tests for Zippers – Bottom Stop Holding Strength, Crosswise |
| ASTM D2061-30.3 | Strength Tests for Zippers – Separating Unit Strength, Crosswise |
| ASTM D2061-72-81 | Strength Tests for Zippers – Resistance to Pull-Off of Slider Pull |
| ASTM D2061-92-100 | Strength Tests for Zippers – Holding Strength of Slider Lock |
| ASTM D2097 | Flex Testing of Finish on Upholstery Leather |
| ASTM D2122 | Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D2124 | Analysis of Components in Poly(Vinyl Chlo.) Compounds Using an Infrared Spectrophotometric Technique |
| ASTM D2126 | Response of Rigid Cellular Plastics to Thermal and Humid Aging |
| ASTM D2130 | Standard Test Method for Diameter of Wool and Other Animal Fibers by Microprojection |
| ASTM D2136 | Coated Fabrics – Low-Temperature Bend Test |
| ASTM D2137 | Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics |
| ASTM D2165 | pH of Aqueous Extracts of Wool and Similar Animal Fibers |
| ASTM D2196 | Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer |
| ASTM D2199 | Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D2208 | Breaking Strength of Leather by the Grab Method |
| ASTM D2209 | Tensile Strength of Leather |
| ASTM D2212 | Slit Tear Resistance of Leather |
| ASTM D2240 | Rubber Property – Durometer Hardness |
| ASTM D2256 | Tensile Properties of Yarns by the Single-Strand Method |
| ASTM D2259 | Shrinkage of Yarns – Boiling Water Exposure |
| ASTM D2259 | Shrinkage of Yarns – Dry-Heat Exposure |
| ASTM D2261 | Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (CRE Testing Machine) |
| ASTM D228 PULL-THROU | Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing – Fastener Pull-Through Resistance |
| ASTM D228 PULL-THROU | Fastener Pull-Through Resistance (ASTM D3462) |
| ASTM D2290 | Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM D2344 | Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates. |
| ASTM D2369 | Volatile Content of Coatings |
| ASTM D2370 | Tensile Properties of Organic Coatings |
| ASTM D2412 | Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D2412 | Rigidity test (ASTM D2412) |
| ASTM D2412 | Joints crushing strength (ASTM D2412) |
| ASTM D2444 | Impact strength test (ASTM D2444) |
| ASTM D2457 | Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D256 | Determining the Izod Pendulum Impact Resistance of Plastics |
| ASTM D2565 | Xenon Arc Exposure of Plastics Intended for Outdoor Applications |
| ASTM D2582 | Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting |
| ASTM D2583 | Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D2584 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D2594 | Stretch Properties of Knitted Fabrics Having Low Power |
| ASTM D2697 | Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D2724 BOND STRE | Bond Strength of Bonded, Fused, and Laminated Apparel Fabrics |
| ASTM D2734 | Constituent Content of Composite Materials – Void Content |
| ASTM D276 DSC | Identification of Fibers in Textile – Fiber Melting Point by DSC |
| ASTM D276 SOLUBIILTY | Identification of Fibers in Textiles |
| ASTM D2794 | Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D2807 | Chromic Oxide in Leather (Perchloric Acid Oxidation) |
| ASTM D2810 | pH of Leather |
| ASTM D2842 | Water Absorption of Rigid Cellular Plastics |
| ASTM D2859 | Ignition Characteristics of Finished Textile Floor Covering Materials |
| ASTM D3015 | Microscopical Examination of Pigment Dispersion in Plastic Compounds |
| ASTM D3039 | Tensile Properties of Polymer Matrix Composite Materials |
| ASTM D3042 | Insoluble Residue in Carbonate Aggregates |
| ASTM D3045 | Heat Aging of Plastics Without Load |
| ASTM D3080 | Direct Shear Test of Soils Under Consolidated Drained Conditions |
| ASTM D3080 | Direct Shear Test of Soils Under Consolidated Drained Conditions |
| ASTM D3083 SOIL | Flexible Poly (Vinyl Chloride) Plastic Sheeting for Pond, Canal, and Reservoir Lining – Soil Burial |
| ASTM D3083 TENSILE | Flexible Poly(Vinyl Chloride) Plastic Sheeting for Pond, Canal, and Reservoir Lining – Tensile Strength |
| ASTM D3083 WATER-EXT | Flexible Poly(Vinyl Chloride) Plastic Sheeting for Pond, Canal, and Reservoir Lining – Water Extraction |
| ASTM D3107 | Stretch Properties of Fabrics Woven from Stretch Yarns |
| ASTM D3163 | Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
| ASTM D3167 | Floating Roller Peel Resistance of Adhesives |
| ASTM D3171 | Constituent Content of Composite Materials – Void Content |
| ASTM D3273 | Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D3285 | Water Absorptiveness of Nonbibulous Paper and Paperboard (Cobb Test) |
| ASTM D3330 | Peel Adhesion of Pressure-Sensitive Tape |
| ASTM D3350 THERMSTAB | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials – Thermal Stability |
| ASTM D3359 | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM D3359 | Standard Test Methods for Rating Adhesion by Tape Test – Method B – Cross-Cut Tape Test |
| ASTM D3363 | Standard Test Method for Film Hardness by Pencil Test |
| ASTM D3389 | Coated Fabrics Abrasion Resistance (Rotary Platform Abrader) |
| ASTM D3393 | Standard Specification for Coated Fabrics – Waterproofness |
| ASTM D3410 | Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading |
| ASTM D3417 | Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry (DSC) |
| ASTM D3418 | Transition Temp. and Enthalpies of Fusion and Crystal. of Polymers by Differential Scan. Calorimetry |
| ASTM D3495 | Hexane Extraction of Leather |
| ASTM D3512 | Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Random Tumble Pilling Tester |
| ASTM D3574 A | Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams – Density Test |
| ASTM D3574 B1 | Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams – Test B1 Indent. Force Deflection |
| ASTM D3574 C | Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams – Compression Deflection Test |
| ASTM D3574 D | Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams – Deflection Compression Set |
| ASTM D3574 E | Flexible Cellular Materials – Slab, Bonded, and Molded Urethane Foams – Tensile Test |
| ASTM D3574 I5 | Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams – Dynamic Fatigue Test by Constant Deflection Pounding |
| ASTM D3575 COMP | Flexible Cellular Materials Made From Olefin Polymers – Suffix D (Compression Deflection) |
| ASTM D3575 COMP | Flexible Cellular Materials Made From Olefin Polymers – Suffix D (Compression Deflection) |
| ASTM D3575 COMP-SET | Flexible Cellular Materials Made From Olefin Polymers – Suffix B: Compression Set Under Constant Deflect. |
| ASTM D3575 DENSITY | Flexible Cellular Materials Made From Olefin Polymers – Suffix W (Density -Method A) |
| ASTM D3575 DENSITY | Flexible Cellular Materials Made From Olefin Polymers Suffix W – Density (Method A) |
| ASTM D3575 DIMENSION | Flexible Cellular Materials Made From Olefin Polymers – Dimensions |
| ASTM D3597 ABRASION | Surface Abrasion |
| ASTM D3597 CF SOLVEN | Colorfastness to Solvent |
| ASTM D3597 CF WATER | Colorfastness to Water |
| ASTM D3759 | Breaking Strength and Elongation of Pressure-Sensitive Tape |
| ASTM D3763 | High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D3767 | Rubber-Measurement of Dimensions |
| ASTM D3774 | Width of Textile Fabric |
| ASTM D3775 | Warp (End) and Filling (Pick) Count of Woven Fabrics |
| ASTM D3775 | End (Warp) and Pick (Filling) Count of Woven Fabrics |
| ASTM D3776 | Mass per Unit Area (Weight) of Fabric |
| ASTM D3786 | Bursting Strength of Textile Fabrics – Diaphragm Bursting Strength Tester Method |
| ASTM D3816 | Water Penetration Rate of Pressure-Sensitive Tapes |
| ASTM D3822 | Tensile Properties of Single Textile Fibers |
| ASTM D3823 | Determining Ticket Numbers for Sewing Threads |
| ASTM D3833 | Water Vapor Transmission of Pressure-Sensitive Tapes |
| ASTM D3846 | In-Plane Shear Strength of Reinforced Plastics |
| ASTM D3882 | Bow and Skew in Woven and Knitted Fabrics |
| ASTM D3884 | Abrasion Resistance of Textile Fabrics (Rotary Platform Abrader Method) |
| ASTM D3885 | Abrasion Resistance of Textile Fabrics (Flexing and Abrasion Method) — Cycles to Rupture |
| ASTM D3886 | Abrasion Resistance of Textile Fabrics (Inflated Diaphragm Apparatus) |
| ASTM D3887 FAB COUNT | Standard Specification for Tolerances for Knitted Fabrics – Fabric Count |
| ASTM D3895 | Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
| ASTM D3939 | Snagging Resistance of Fabrics (Mace) |
| ASTM D3950 | Standard Specification for Strapping, Nonmetallic (and Joining Methods) |
| ASTM D3985 | Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D4028 BREAKING | Breaking Strength |
| ASTM D4034 | « Resistance to Yarn Slippage at the Sewn Seam in Woven Upholstery Fabrics » |
| ASTM D4060 | Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D4065 | Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D4068 WATERPROO | Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane – Hydrostatic Pressure Resistance |
| ASTM D4068 WATERPROO | American National Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation – Waterproofness |
| ASTM D4073 | Tensile-Tear Strength of Bituminous Roofing Membranes |
| ASTM D4108 | « Thermal Protective Performance of Materials for Clothing by Open-Flame Method » |
| ASTM D412 | Vulcanized Rubber and Thermoplastic Elastomers-Tension |
| ASTM D413 | Rubber Property — Adhesion to Flexible Substrate |
| ASTM D4138 | Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D4157 | Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method) |
| ASTM D418 21 BINDING | Pile Yarn Floor Covering Construction – Number of Binding Sites per Unit Length or Width |
| ASTM D418 COMP MASS | Pile Yarn Floor Covering Construction – Component Masses per Unit Area |
| ASTM D418 TOTAL MASS | Pile Yarn Floor Covering Construction – Total Mass per Unit Area |
| ASTM D418 TUFTHEIGHT | Pile Yarn Floor Covering Construction – Tuft Height |
| ASTM D4218 | Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique |
| ASTM D422 | Particle-Size Analysis of Soils (hydrometer test only) |
| ASTM D422 | Particle-Size Analysis of Soils (sieving only) |
| ASTM D422 | Particle-Size Analysis of Soils (sieving and hydrometer test) |
| ASTM D4226 | Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D4329 | Fluorescent UV Exposure of Plastics |
| ASTM D434 | Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam |
| ASTM D4355 | Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus |
| ASTM D4355 | Effect of Exposure of Unreinforced Polyolefin Geomembrane Using Fluorescent UV Condensation Apparatus |
| ASTM D4355 | Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus |
| ASTM D4355 | Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus |
| ASTM D4400 | Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM D4459 | Xenon-Arc Exposure of Plastics Intended for Indoor Applications |
| ASTM D4475 | Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method |
| ASTM D4491 | Water Permeability of Geotextiles by Permittivity |
| ASTM D4496 | D-C Resistance or Conductance of Moderately Conductive Materials |
| ASTM D4501 | Shear Strength of Adhesive Bonds Between Rigid Substrates by the Block-Shear Method |
| ASTM D4533 | Trapezoid Tearing Strength of Geotextiles |
| ASTM D4541 | Standard Test Method for Pull Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D4587 | Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM D4591 | Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
| ASTM D4595 | Tensile Properties of Geotextiles by the Wide-Width Method |
| ASTM D4603 | « Standard Test Method for Determining Inherent Viscosity of Poly (Ethylene Terephthalate) (PET) by Glass Capillary Viscometer » |
| ASTM D4632 | Geosynthetic Clay Liner Peel Strength Procedure |
| ASTM D4632 | Grab Breaking Load and Elongation of Geotextiles |
| ASTM D4703 | Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D4704 | Tearing Strength, Tongue Tear of Leather |
| ASTM D471 | Standard Test Method for Rubber Property – Effect of Liquids |
| ASTM D4716 | Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head |
| ASTM D4751 | Determining Apparent Opening Size of a Geotextile |
| ASTM D4770 | Appearance and Integrity of Highloft Batting After Refurbishing |
| ASTM D4772 | Surface Water Absorption of Terry Fabrics (Water Flow) |
| ASTM D4786 | Stitch Tear Strength, Single Hole |
| ASTM D4798 | Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method) |
| ASTM D4812 | Unnotched Cantilever Beam Impact Resistance of Plastics |
| ASTM D4833 | Index Puncture Resistance of Geomembranes and Related Products |
| ASTM D4833 | Index Puncture Resistance of Geotextiles, Geomembranes and Related Products |
| ASTM D4851 BREAK | Coated and Laminated Fabrics for Architectural Use – Fabric Breaking Force |
| ASTM D4851 BREAK | « Coated and Laminated Fabrics for Architectural Use – Breaking Force and Elongation at Break » |
| ASTM D4851 BREAK | « Coated and Laminated Fabrics for Architectural Use – Breaking Force After Crease Fold » |
| ASTM D4851 CREEP | Coated and Laminated Fabrics for Architectural Use – Uniaxial Elongation Under Static Load |
| ASTM D4851 CREEP | Coated and Laminated Fabrics for Architectural Use – Uniaxial Elongation Under Static Load |
| ASTM D4851 CREEP | Coated and Laminated Fabrics for Architectural Use – Creep load test under extreme temperatures |
| ASTM D4869 LWT | Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing – Liquid Water Transmission |
| ASTM D4869 LWT | Liquid Water Transmission (ASTM D4869) |
| ASTM D4884 | Strength of Sewn or Bonded Seams of Geotextiles |
| ASTM D4885 | Performance Strength of Geomembranes by the Wide Width Strip Tensile Method |
| ASTM D4886 | « Abrasion Resistance of Geotextiles (Sand Paper/Sliding Block Method) » |
| ASTM D4912 | Fabric Stability of Vinyl-Coated Glass Yarn Insect Screening and Louver Cloth |
| ASTM D4966 | Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method) |
| ASTM D4970 | Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Martindale Tester |
| ASTM D5034 | Acceptance Criteria for Water-Resistive Barriers – Tensile |
| ASTM D5034 | Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
| ASTM D5034 | Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
| ASTM D5045 | Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials |
| ASTM D5052 | Permeability of Leather to Water Vapor |
| ASTM D5053 | Colorfastness of Crocking of Leather |
| ASTM D5083 | Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens |
| ASTM D5084 | Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter |
| ASTM D5101 | Standard Test Method for Measuring the Filtration Compatibility of Soil-Geotextile Systems Clogging Potential by the Gradient Ratio |
| ASTM D5103 | « Length and Length Distribution of Manufactured Staple Fibers (Single-Fiber Test) » |
| ASTM D5116 | Small-Scale Environmental Chamber Determinations of Organic Emissions from Indoor Materials/Products |
| ASTM D5147 TENSILEAR | Sampling and Testing Modified Bituminous Sheet Material – Load Strain Properties |
| ASTM D5147 TENSILEAR | Sampling and Testing Modified Bituminous Sheet Material – Load Strain Properties |
| ASTM D5147 WATERABS | Sampling and Testing Modified Bituminous Sheet Material – Water absorption |
| ASTM D5169 | « Shear Strength (Dynamic Method) of Hook and Loop Touch Fasteners » |
| ASTM D5170 | Peel Strength (« T » Method) of Hook and Loop Touch Fasteners |
| ASTM D5179 | Measuring Adhesion of Organic Coatings to Plastic Substrates by Direct Tensile Testing |
| ASTM D5199 | Measuring the Nominal Thickness of Geosynthetics |
| ASTM D522 | Mandrel Bend Test of Attached Organic Coatings |
| ASTM D523 | Specular Gloss |
| ASTM D5261 | Mass per Unit Area of Geotextiles |
| ASTM D5321 | Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces by Direct Shear |
| ASTM D5322 | Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthtics to Liquids |
| ASTM D5323 | Standard Practice for Determination of 2 % Secant Modulus for Polyethylene Geomembranes |
| ASTM D5323 | Standard Practice for Determination of 2 % Secant Modulus for Polyethylene Geomembranes |
| ASTM D5379 | Shear Properties of Composite Materials by the V-Notched Beam Method |
| ASTM D5385 | Hydrostatic Pressure Resistance of Waterproofing Membranes |
| ASTM D5397 | Evaluation of Stress Crack Resistance of Polyolefin Geomembranes Using Notched Constant Tensile Load Test |
| ASTM D5402 | « Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs – Method A » |
| ASTM D5420 | Impact Resistance of Flat, Rigid Plastic Specimen by Mean of a Striker Impacted by a Falling Weight |
| ASTM D543 | Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D5493 | Permittivity of Geotextiles Under Load |
| ASTM D5514 | Large Scale Hydrostatic Puncture Testing of Geosynthetics |
| ASTM D5528 | Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
| ASTM D5587 | Tearing Strength of Fabrics by Trapezoid Procedure |
| ASTM D5596 | Microscopic Evaluation of the Dispersion of Carbon Black in Polyolefin Geosynthetics |
| ASTM D5602 | Static Puncture Resistance of Roofing Membrane Specimens |
| ASTM D5617 | Multi-Axial Tension Test for Geosynthetics |
| ASTM D5628 | Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM D5630 | Standard Test Method for Ash Content in Plastics |
| ASTM D5635 | Dynamic Puncture Resistance of Roofing Membrane Specimens |
| ASTM D5636 | Low Temperature Unrolling of Felt or Sheet Roofing and Waterproofing Materials |
| ASTM D5644 | Determination of Particle Size Distribution of Recycled Vulcanizate Particula Rubber |
| ASTM D568 | Rate of Burning and/or Extent and Time of Burning of Flexible Plastics in a Vertical Position |
| ASTM D570 | Standard Test Method for Water Absorption of Plastics |
| ASTM D5721 | Air Oven Aging of Polyolefin Geomembranes |
| ASTM D573 | Standard Test Method for Rubber – Deterioration in an Air Oven |
| ASTM D5733 | Tearing Strength of Nonwoven Fabrics by the Trapezoid Procedure |
| ASTM D5747 IMMERSION | Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids |
| ASTM D5748 | Protrusion Puncture Resistance of Stretch Wrap Film |
| ASTM D575 | Standard Test Methods for Rubber Properties in Compression |
| ASTM D5793 | Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings |
| ASTM D5813 | Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM D5848 TOTALMASS | Mass Per Unit Area of Pile Yarn Floor Coverings – Total Mass Per Unit Area |
| ASTM D5849 | Evaluating Resistance of Modified Bituminous Roofing Membrane to Cyclic Fatigue (Joint Displacement) |
| ASTM D5868 | Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding |
| ASTM D5884 | Determining Tearing Strength of Internally Reinforced Geomembranes |
| ASTM D5885 | Oxidative-Induction Time of Polyolefins Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM D5887 | Measurement of Index Flux Through Saturated GCL Specimen Using a Flexible Wall Permeameter |
| ASTM D5890 | Swell Index of Clay Mineral Component of Geosynthetic Clay Liners |
| ASTM D5891 | Fluid Loss of Clay Component of Geosynthetic Clay Liners |
| ASTM D5947 | Physical Dimensions of Solid Plastics Specimens |
| ASTM D5947 | Compostable Product’s Thickness |
| ASTM D5961 | Bearing Response of Polymer Matrix Composite Laminates |
| ASTM D5993 | Test Method for Measuring Mass Per Unit of Geosynthetic Clay Liners |
| ASTM D5994 | Core Thickness of Textured Geomembrane |
| ASTM D6015 | Static Water Absorption of Leather |
| ASTM D6075 | Cracking Resistance of Leather |
| ASTM D6108 | Compressive Properties of Plastic Lumber and Shapes |
| ASTM D6109 | Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products |
| ASTM D6111 | Bulk Density and Specific Gravity of Plastic Lumber and Shapes by Displacement |
| ASTM D6117 | Mechanical Fasteners in Plastic Lumber and Shapes |
| ASTM D6140 | Determine Asphalt Retention of Paving Fabrics Used in Asphalt Paving for Full-Width Applications |
| ASTM D624 | Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers |
| ASTM D6241 | Measuring Static Puncture Strength of Geotextiles and Geosynthetic-Related Products Using a 50 mm Probe |
| ASTM D6243 | Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method |
| ASTM D6243 | Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method |
| ASTM D6243 | Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method |
| ASTM D629 | Quantitative Analysis of Textiles |
| ASTM D635 | Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
| ASTM D6364 | Standard Test Method for Determining the Short-Term Compression Behavior of Geosynthetics |
| ASTM D6370 | Rubber – Compositional Analysis by Thermogravimetry (TGA) |
| ASTM D638 | Tensile Properties of Plastics |
| ASTM D6382 | Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material |
| ASTM D6392 | Determining the Integrity of Nonreinforced Geomembrane-Seams Produced Using Thermo-Fusion Methods |
| ASTM D6413 | Flame Resistance of Textiles (Vertical Test) |
| ASTM D6454 | Short-Term Compression Behavior of Turf Reinforcement Mats (TRMs) |
| ASTM D6475 | Mass Per Unit Area of Erosion Control Blankets |
| ASTM D6496 | Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners |
| ASTM D6524 | Measuring the Resiliency of Turf Reinforcement Mats (TRMs) |
| ASTM D6525 | Measuring Nominal Thickness of Rolled Erosion Control Products |
| ASTM D6566 | Mass per Unit Area of Turf Reinforcement Mats |
| ASTM D6567 | Measuring the Light Penetration of a Rolled Erosion Control Product (RECP) |
| ASTM D6574 | Determining the (In-plane) Hydraulic Transmissivity of a Geosynthetic by Radial Flow |
| ASTM D6575 | « Stiffness of Geosynthetics Used as Turf Reinforcement Mats (TRMs) » |
| ASTM D6614 | Stretch Properties of Textile Fabrics – CRE Method |
| ASTM D6637 | Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method; Method A (Single Rib) |
| ASTM D6637 | Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method; Method B (Wide Width) |
| ASTM D6641 | Compressive Properties of Polymer…Materials Using a Combined Loading Compression Test Fixture |
| ASTM D6693 | Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembrane |
| ASTM D6701 | Standard Test Method for Determining Water Vapor Transmission Rates Through Nonwoven and Plastic Barriers |
| ASTM D6707 CLASS | Classification of the Tested Product |
| ASTM D6766 | Evaluation of Hydraulic Properties of GCL Permeated with Potentially Incompatible Aqueous Solutions |
| ASTM D6768 | Tensile Strength of Geosynthetic Clay Liners |
| ASTM D6775 | Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material |
| ASTM D6797 | « Bursting Strength of Fabrics Constant-Rate-of-Extension (CRE) Ball Burst Test – After Laundering » |
| ASTM D6818 | Ultimate Tensile Properties of Roller Erosion Control Products |
| ASTM D6862 | 90 Degree Peel Resistance of Adhesives |
| ASTM D695 | Compressive Properties of Rigid Plastics |
| ASTM D696 | Coefficient of Linear Thermal Expansion of Plastics Between -30C and 30C With a Vitreous Dilatometer |
| ASTM D6962 | Operation of a Roller Chair Tester for Pile Yarn Floor Coverings ***MC OK 10-09-2019 |
| ASTM D6980 | Determination of Moisture in Plastics by Loss in Weight |
| ASTM D6988 | Determination of Thickness of Plastic Film Test Specimens |
| ASTM D6992 | Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
| ASTM D7003 | Strip Tensile Properties of Reinforced Geomembranes |
| ASTM D7004 | Grab Tensile Properties of Reinforced Geomembranes |
| ASTM D7005 | Bond Strength (Ply Adhesion) of Geocomposites |
| ASTM D7028 | Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis |
| ASTM D7056 | Determining the Tensile Shear Strength of Pre-Fabricated Bituminous Geomembrane Seams |
| ASTM D7078 | Shear Properties of Composite Materials by V-Notched Rail Shear Method |
| ASTM D7091 | Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D7136 | Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event |
| ASTM D7138 | Determine Melting Temperature of Synthetic Fibers |
| ASTM D7142 | Holding Strength of Prong-Ring Attached Snap Fasteners |
| ASTM D7179 | Determining Geonet Breaking Force |
| ASTM D7192 | High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors |
| ASTM D7234 | Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D7238 | Effect of Exposure of Unreinforced Polyolefin Geomembrane Using Fluorescent UV Condensation Apparatus |
| ASTM D7249 | Facesheet Properties of Sandwich Constructions by Long Beam Flexure |
| ASTM D7250 | Determining Sandwich Beam Flexural and Shear Stiffness |
| ASTM D7255 | Abrasion Resistance of Leather (Rotary Platform, Abraser Method) |
| ASTM D7264 | Flexural Properties of Polymer Matrix Composite Materials |
| ASTM D7272 | Determining the Integrity of Seams Used in Joining Geomembranes by Pre-manufactured Taped Methods |
| ASTM D7275 | Tensile Properties of Bituminous Geomembranes |
| ASTM D7291 | Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a …Composite Material |
| ASTM D7332 | Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite |
| ASTM D7361 | Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
| ASTM D737 | Air Permeability of Textile Fabrics |
| ASTM D7408 | Non-Reinforced PVC (Polyvinyl Chloride) Geomembrane Seams |
| ASTM D7409 | Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns |
| ASTM D746 | Brittleness Temperature of Plastics and Elastomers by Impact |
| ASTM D7466 | Measuring the Asperity Height of Textured Geomembranes |
| ASTM D7490 | Measurement of the Surface Tension of Solid Coatings, Substrates and Pigments using Contact Angle Measurements |
| ASTM D751 ADHESION | Standard Test Method for Coated Fabrics – Adhesion of Coating to Fabric |
| ASTM D751 BLOCKING | « Standard Test Method for Coated Fabrics – Blocking Resistance at Elevated Temperature » |
| ASTM D751 BREAK-A | « Standard Test Method for Coated Fabrics – Breaking Strength-Grab Test Method (Procedure A) » |
| ASTM D751 BREAK-B | « Standard Test Method for Coated Fabrics – Breaking Strength – Cut Strip Test Method (Procedure B) » |
| ASTM D751 BURST DYN | « Standard Test Method for Coated Fabrics – Bursting Strength Procedure A – Ball Burst » |
| ASTM D751 BURST MULL | Standard Test Method for Coated Fabrics – Bursting Strength |
| ASTM D751 BURST MULL | « Standard Test Method for Coated Fabrics – Bursting Strength Procedure B – Diaphragm Burst Method » |
| ASTM D751 CRACK-RES | Standard Test Method for Coated Fabrics – Low-Temperature Crack Resistance |
| ASTM D751 DIMENSIONS | Standard Test Method for Coated Fabrics – Length & Width |
| ASTM D751 HYDROST-A | « Standard Test Method for Coated Fabrics – Hydrostatic Resistance: Mullen Tester (Procedures A-1) » |
| ASTM D751 HYDROST-B | « Standard Test Method for Coated Fabrics – Hydrostatic Resistance: Rising Column of Water (Procedure B-2) » |
| ASTM D751 LOW BEND | « Standard Test Method for Coated Fabrics – Low-Temperature Bend Test » |
| ASTM D751 MASS | Standard Test Method for Coated Fabrics – Mass |
| ASTM D751 PUNCTURE | Standard Test Method for Coated Fabrics – Puncture Resistance (ball) |
| ASTM D751 PUNCTURE | Standard Test Method for Coated Fabrics – Puncture Resistance |
| ASTM D751 SEAM-STREN | Standard Test Methods for Coated Fabrics – Seam Strength |
| ASTM D751 STREN COAT | Standard Test Method for Coated Fabrics – Strength of Coating |
| ASTM D751 TEAR-A | « Standard Test Method for Coated Fabrics – Tearing Strength – Pendulum Method (Procedure A) » |
| ASTM D751 TEAR-B | « Standard Test Method for Coated Fabrics – Tearing Strength – Tongue Tear Method (Procedure B) » |
| ASTM D751 TEAR-TRAP | Standard Test Method for Coated Fabrics – Trapezoidal Tear |
| ASTM D751 THICKNESS | Standard Test Method for Coated Fabrics – Thickness |
| ASTM D7570 | Evaluation of Dimensional Stability of Pile Yarn Floor Covering |
| ASTM D7616 | Determining Apparent Overlap Splice Shear Strength Properties of Wet Lay-Up Fiber-Reinforced Polymer Matrix Composites Used for Strengthening Civil Structures |
| ASTM D7635 | Measurement of Thickness of Coatings Over Fabric Reinforcement |
| ASTM D7672 COMP | Evaluating Structural Capacities of Rim Board Products and Assemblies – Direct Test of Uniform Vertical Load Transfer |
| ASTM D7706 | Standard Practice for Rapid Screening of VOC Emissions from Products Using Micro-Scale Chambers |
| ASTM D7737 | Individual Geogrid Junction Strength |
| ASTM D774 | Bursting Strength of Paper |
| ASTM D7747 | Determ.Integrity of Seams Produced Using Thermo-Fusion Meth.forReinforced Geom.by Strip Tensile Method |
| ASTM D7748 | Flexural Rigidity of Geogrids, Geotextiles and Related Products |
| ASTM D7749 | Determ. Integrity of Seams Produced Using Thermo-Fusion Meth. for Reinforced Geom. by the Grab Method |
| ASTM D7766 | Damage Resistance Testing of Sandwich Constructions |
| ASTM D779 | Determining the Water Vapor Resistance of Sheet Materials in Contact with Liquid Water by the Dry Indicator Method |
| ASTM D7864 | Determining the Aperture Stability Modulus of Geogrids |
| ASTM D790 | Flexural Properties of Unreinforced Plastics and Electrical Insulating Materials |
| ASTM D7905 | Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
| ASTM D792 | Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D792 | Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D7984 | Measurement of Thermal Effusivity of Fabrics Using a MTPS Instrument |
| ASTM D8007 | Standard Test Method for Wale and Course Count of Weft Knitted Fabrics |
| ASTM D8117 | Oxidative Induction Time of Polyolefins Geosynthetics by Differential Scanning Calorimetry |
| ASTM D814 | Rubber Property – Vapor Transmission of Volatile Liquids |
| ASTM D816 | Standard Test Methods for Rubber Cements |
| ASTM D8257 THERM-CYC | Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing – Thermal Cycling |
| ASTM D828 | Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus |
| ASTM D8490 | Determining the Opening Size of Circular Knit Geotextiles Using an Optical Method |
| ASTM D882 | Tensile Properties of Thin Plastic Sheeting |
| ASTM D903 | Peel or Stripping Strength of Adhesive Bonds |
| ASTM E1131 | Compositional Analysis by Thermogravimetry |
| ASTM E1131 | Thermogravimetry Analysis |
| ASTM E1164 | Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E1252 | Infrared Spectrum |
| ASTM E1252 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E1269 | Determining Specific Heat Capacity by Differential Scanning Calorimetry |
| ASTM E1354 | Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E1356 | Glass Transition Temperatures by Differential Scanning Calorimetry |
| ASTM E136 | Behavior of Materials in a Vertical Tube Furnace at 750°C |
| ASTM E1476 | Standard Guide for Metals Identification, Grade Verification, and Sorting – X-ray Fluorescence Spectrometry Method |
| ASTM E154 PUNCT | Water Vapor Retarders …- Resistance to Puncture |
| ASTM E154 TENSILE | Tensile Strength (ASTM D882) |
| ASTM E154 TENSILE | Tensile Strength of New Material |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) after Plastic Flow and Elevated Temperature |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) after Low Temperature Flexibility |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) after Exposure to Organisms and Substances in Contacting Soil |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) after Exposure to Petroleum Vehicles for Soil Poisons |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) after UV Exposure |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) |
| ASTM E154 WVT | Water Vapor Transmission of Materials (ASTM E96/E96M) after Wetting and Drying and Long-Time Soaking |
| ASTM E154 WVT | Permeance of New Material |
| ASTM E154 WVT | Permeance after Wetting, Drying, and Soaking |
| ASTM E154 WVT | Permeance after Heat Conditioning |
| ASTM E154 WVT | Permeance after Low Temperature Conditioning |
| ASTM E154 WVT | Permeance after Soil Organism Exposure |
| ASTM E154 WVT | Permeance after Soil Poison Petroleum Vehicle Exposure |
| ASTM E154 WVT | Permeance after Exposure to Ultraviolet Light |
| ASTM E162 | Surface Flammability of Materials Using a Radiant Heat Energy Source |
| ASTM E2149 | Antimicrobial Activity of Antimicrobial Agents Under Dynamic Contact Conditions |
| ASTM E2178 | Air Permeance of Building Materials |
| ASTM E2178 | Air Permeance (ASTM E2178) |
| ASTM E2178 | Acceptance Criteria for Water-Resistive Barriers – Air Permeance |
| ASTM E2180 | Standard Test Method for Determining the Activity of Incorporated Antimicrobial Agent(s) In Polymeric or Hydrophobic Materials |
| ASTM E2254 | Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E2397 GRO-MEDIA | Determination of Dead Loads and Live Loads Associated with Vegetative (Green) Roof Systems – Weight of Growth Media |
| ASTM E2399 | « Maximum Media Density for Dead Load Analysis of Vegetative (Green) Roof Systems » |
| ASTM E2550 | Thermal Stability by Thermogravimetry |
| ASTM E2556 AGING | Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment – Accelerated Aging |
| ASTM E2556 PLIABILIT | Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment – Pliability |
| ASTM E2556 WATERPOND | Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment – Water Ponding Test |
| ASTM E2556 WATERPOND | Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment – Water Ponding Test after UV Exposure |
| ASTM E2556 WATERPOND | Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment – Water Ponding Test after UV Exposure and Accelerated Aging |
| ASTM E2602 | Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E308 | Computing the Colors of Objects by Using the CIE System |
| ASTM E313 | Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates |
| ASTM E424 | Solar Energy Reflectance (Terrestrial) of Sheet Materials – Method A |
| ASTM E648 | Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source |
| ASTM E661 | Performance of Wood and Wood-Based Floor and Roof Sheating … – Concentrated Static Load Test |
| ASTM E661 | Performance of Wood and Wood-Based Floor and Roof Sheating … – Impact Test |
| ASTM E662 | Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM E794 | Melting and Crystallization Temperature by Thermal Analysis |
| ASTM E8 | Tension Testing of Metallic Materials |
| ASTM E809 CERT | Standard Practice for Measuring Photometric Characteristics of Retroreflectors |
| ASTM E810 | Standard Test Method for Coefficient of Retroreflection of Retroreflective Sheeting Utilizing the Coplanar Geometry |
| ASTM E831 | Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis |
| ASTM E9 | Compression Testing of Metallic Materials at Room Temperature |
| ASTM E903 | Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres |
| ASTM E96 | Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E96 | Water Vapor Transmission (ASTM E96) |
| ASTM E96 | Water Vapour Permeance (ASTM E96) |
| ASTM E96 | Acceptance Criteria for Water-Resistive Barriers – Water Vapor Transmission |
| ASTM F1055 PEEL | Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing – Peel Test |
| ASTM F1060 | Evaluation of Conductive and Compressive Heat Resistance (CCHR) |
| ASTM F1087 | Linear Dimensional Stability of a Gasket Material to Moisture |
| ASTM F1087 | Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing – Dimensional Stability |
| ASTM F1249 | Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM F1291 | Measuring the Thermal Insulation of Clothing Using a Heated Manikin |
| ASTM F1306 | Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates |
| ASTM F1342 | Protective Clothing Material Resistance to Puncture |
| ASTM F1358 | Effects of Flame Impingement on Materials Used in Protective Clothing Not Designated Primarily for Flame Resistance |
| ASTM F1359 | Liquid Penetration Resistance of Protective Clothing or Protective Ensembles Under a Shower Spray While on a Manikin |
| ASTM F137 | Flexibility of Resilient Flooring Materials with Cylindrical Mandrel Apparatus |
| ASTM F1670 | Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood |
| ASTM F1671 | « Resistance of Materials to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage – After laundering » |
| ASTM F1790 | Measuring Cut Resistance of Materials Used in Protective Clothing |
| ASTM F1862 | Resistance of Medical Face Masks to Penetration by Synthetic Blood (Horizontal Projection of Fixed Volume at a Known Velocity) |
| ASTM F1868 | Thermal Resistance, Evaporative Resistance, and Total Heat Loss Measurements of Clothing Materials Using a Sweating Hot Plate – Part A + B |
| ASTM F1868 | Thermal Resistance, Evaporative Resistance, and Total Heat Loss Measurements of Clothing Materials Using a Sweating Hot Plate – Part A |
| ASTM F1868 | Thermal Resistance, Evaporative Resistance, and Total Heat Loss Measurements of Clothing Materials Using a Sweating Hot Plate – Part B |
| ASTM F1868 | Thermal Resistance, Evaporative Resistance, and Total Heat Loss Measurements of Clothing Materials Using a Sweating Hot Plate – Part C: THL |
| ASTM F1891 STIFFNES | Stiffness of rainwear fabrics |
| ASTM F1891 TEARING | Tearing Strength — Trapezoid Procedure |
| ASTM F1914 | Short-Term Indentation and Residual Indentation of Resilient Floor Covering |
| ASTM F1930 | « Flame Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin » |
| ASTM F1939 | « Radiant Heat Resistance of Flame Resistant Clothing Materials with Continuous Heating » |
| ASTM F1959 | Determining the Arc Rating of Materials for Clothing |
| ASTM F1980 | Accelerated Aging of Sterile Barrier Systems and Medical Devices |
| ASTM F2101 | Evaluating the Bacterial Filtration Efficiency (BFE) of Medical Face Mask Materials, Using a Biological Aerosol of Staphylococcus aureus |
| ASTM F2136 | Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe |
| ASTM F2203 | Linear Measurement Using Precision Steel Rule |
| ASTM F2299 | Determining the Initial Efficiency of Materials Used in Medical Face Masks to Penetration by Particulates Using Latex Spheres |
| ASTM F2733 TEARING | Trapezoidal Tearing Resistance |
| ASTM F2878 | Protective Clothing Material Resistance to Hypodermic Needle Puncture |
| ASTM F2894 | Evaluation of Materials, Protective Clothing, and Equipment for Heat Resistance Using a Hot Air Circulating Oven |
| ASTM F2907 | Standard Consumer Safety Specification for Sling Carriers – Laundering |
| ASTM F2907 | Standard Consumer Safety Specification for Sling Carriers – Permanency of labels and warnings |
| ASTM F2907 | « Standard Consumer Safety Specification for Sling Carriers – Adhesion test for warnings applied directly onto the surface of the product » |
| ASTM F2992 | Measuring Cut Resistance of Materials Used in Protective Clothing with Tomodynamometer (TDM-100) |
| ASTM F392 | Conditioning Flexible Barrier Materials for Flex Durability |
| ASTM F726 COMP-EXT | Sorbent Performance of Adsorbents for use on Crude Oil and Related Spills ***OK 15-06-2018 |
| ASTM F726 DYN-DEGRAD | Sorbent Performance of Adsorbents for use on Crude Oil and Related Spills |
| ASTM F726 OIL-ADS LT | Sorbent Performance of Adsorbents for use on Crude Oil and Related Spills |
| ASTM F88 | Seal Strength of Flexible Barrier Materials |
| ASTM F903 | « Resistance of Materials Used in Protective Clothing to Penetration by Liquids » |
| ASTM F904 | Comparison of Bond Strength or Ply Adhesion of Similar Laminates Made from Flexible Materials |
| ASTM F963 ABUSE TEST | Toy Safety – Abuse Testing |
| ASTM F963 ACC EDGES | Toy Safety – Accessible Edges |
| ASTM F963 ACC POINTS | Toy Safety – Accessible Points |
| ASTM F963 HEAVY ELE | Determination of Heavy Element Content in Toys, Toy Components and Materials |
| ASTM F963 HEAVY ELE | Determination of Heavy Element Content in Toys, Toy Components and Materials |
| ASTM F963 SMALL OBJ | Toy Safety – Small Objects |
| ASTM F970 | Standard Test Method for Measuring Recovery Properties of Floor Coverings after Static Loading |
| ASTM G154 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials |
| ASTM G155 | Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials |
| ASTM G160 | Evaluating Microbial Susceptibility of Nonmetallic Materials by Laboratory Soil Burial |
| ASTM WK46152 SECT.17 | Nonballistic Test Methods for Helmets Worn by Law Enforcement and Corrections – Flammable Liquid Trap Test |
| ATPD 2265 BLOCKING | Blocking |
| ATPD 2265 LOW TEMP | Low temperature crease resistance: Appearance |
| BNQ 1922-900 6.1 | « Face masks for non-medical workers – Attestation Document Maintenance – Option 1 – Washing and Drying » |
| BNQ 1922-900 6.1 | « Face masks for non-medical workers – Attestation Document Maintenance – Option 2 – Dry heat maintenance » |
| BNQ 3624-115 ALLONG | Elongation Test |
| BNQ 3624-115 PULLOUT | Joint Separation (Pull-Out) Resistance Test |
| BS 3424-26 29A | « Resistance to Water Penetration – Low Range Method – 5 min, 25 psi » |
| BS EN 14704-1 | « Determination of the elasticity of fabrics — Part 1: Strip tests » |
| BS EN 20811 | « Determination of resistance to water penetration — Hydrostatic pressure test » |
| BS EN 29073-1 | Methods of tests for nonwovens – Part 1: Determination of mass per unit area |
| BS EN 29073-3 | Methods of tests for nonwovens – Part 3: Determination of tensile strength and elongation |
| BS EN 342 INSPECTION | Visual Inspection |
| BS EN 420 FINGER DEX | Protective gloves – Gloved Finger Dexterity |
| BS EN ISO 105 E01 | Colour fastness to water |
| BS EN ISO 105-D01 | « Colour fastness to dry cleaning using perchloroethylene solvent (ISO 105-D01:2010) » |
| BS EN ISO 9073-4 | Nonwovens – Test methods – Part 4: Determination of tear resistance by the trapezoid procedure |
| BSS 7239 | Boeing — Test method for toxic gas generation by materials on combustion |
| CAL TB 117 SECT 1 | Cover Fabric Test |
| CAL TB 117 SECT 2 | Barrier Materials Test |
| CAL TB 117 SECT 3 | Resilient Filling Material Test |
| CAL TB 117 SECT 4 | Decking Material Test |
| CAL TITLE19 1237.1 | Small Scale Flammability Test |
| CAN 148.1 10 | Geotextiles – Filtration Opening Size |
| CAN 148.1 2 | Mass per Unit Area |
| CAN 148.1 3 | *Thickness of Geotextiles |
| CAN 148.1 4 | Normal Water Permeability Under No Compressive Load |
| CAN 148.1 7.3 | Grab Tensile Test for Geotextiles |
| CAN 155.20 HEAT RES | Heat Resistance |
| CAN 155.20 LABELS | Legibility of labels – After dry cleaning |
| CAN 155.20 LABELS | Legibility of labels – After washing & drying (50 cycles) |
| CAN 155.20 MANIKIN | « Manikin test (flash fire) – As Sold – After washing and drying (1 cycle) » |
| CAN 155.20 MANIKIN | Manikin test (flash fire) – After dry cleaning (1 cycle) |
| CAN 155.20 MANIKIN | Manikin test (flash fire) – After washing and drying (1 cycle) |
| CAN 155.20 THER SHRI | Thermal Shrinkage Resistance |
| CAN 155.22 HEAT RES | Heat Resistance |
| CAN 155.22 PAR 6.1 | Heat resistance and thermal shrinkage tests |
| CAN 155.22 REFLEXION | Visibility Trim |
| CAN 155.22 THER SHRI | Thermal Shrinkage Resistance |
| CAN 182.1 VERTICAL | « Flammability and Labelling requirements for Tents – Vertical test » |
| CAN 37.50 PINHOLING | Hot-Applied, Rubberized Asphalt for Roofing and Waterproofing – Pinholing |
| CAN 37.54 COATTHICK | Polyvinyl Chloride Roofing and Waterproofing Membrane – Coating Thickness |
| CAN 37.54 COATTHICK | Polyvinyl Chloride Roofing and Waterproofing Membrane – Coating Thickness |
| CAN 37.54 THICKNESS | Polyvinyl Chloride Roofing and Waterproofing Membrane – Overall Thickness |
| CAN 37.54 THICKNESS | Polyvinyl Chloride Roofing and Waterproofing Membrane – Overall Thickness |
| CAN 37.56 DIMSTAB | Polymer-Modified Bituminous Membranes for Roofing – Dimensional Stability |
| CAN 37.56 DYNIMPACT | Polymer-Modified Bituminous Membranes for Roofing – Dynamic Impact (Puncturing) |
| CAN 37.56 EMBEDMNT | Polymer-Modified Bituminous Membranes for Roofing – Granule Coverage and Embedment |
| CAN 37.56 HEATCOND | Polymer-Modified Bituminous Membranes for Roofing – Heat Conditioning |
| CAN 37.56 JOINTSTRN | Polymer-Modified Bituminous Membranes for Roofing – Lap Joint Strength |
| CAN 37.56 LT-FLEX | Polymer-Modified Bituminous Membranes for Roofing – Low-Temperature Flexibility |
| CAN 37.56 PLASTFLOW | Polymer-Modified Bituminous Membranes for Roofing – Plastic Flow |
| CAN 37.56 STATPUNCT | Membrane, Modified, Bituminous, Prefabricated, and Reinforced for Roofing – Static Puncturing Test |
| CAN 37.56 STATPUNCT | Polymer-Modified Bituminous Membranes for Roofing – Static Puncturing Test |
| CAN 37.56 STRNENERGY | Polymer-Modified Bituminous Membranes for Roofing – Tensile properties |
| CAN 37.56 TEAR | Polymer-Modified Bituminous Membranes for Roofing – Tear Strength |
| CAN 37.56 THERMSTAB | Polymer-Modified Bituminous Membranes for Roofing – Thermal Stability |
| CAN 37.56 WATERTIGHT | Membrane, Modified, Bituminous, Prefabricated, and Reinforced for Roofing – Watertightness Test |
| CAN 37.56 WATERTIGHT | Polymer-Modified Bituminous Membranes for Roofing – Watertightness Test |
| CAN 37.58 LT-FLEX | Membrane, Elastomeric, Cold-Applied Liquid, for Non-Exposed Use in Roofing and Waterproofing – Low Temperature Flexibility |
| CAN 37.58 STAB-ABS | Membrane, Elastomeric, Cold-Applied Liquid, for Non-Exposed Use in Roofing and Waterproofing – Dimensional Stability and Water Absorption |
| CAN 37.58 WATERTIGHT | Membrane, Elastomeric, Cold-Applied Liquid, for Non-Exposed Use in Roofing ant Waterproofing – Watertightness Test |
| CAN 4.161 CF CLEAN | Carpet for Residential Use – Colourfastness to Wet Cleaning |
| CAN 4.2 11.1 | Bursting Strength – Diaphragm Pressure Test |
| CAN 4.2 11.2 | Bursting Strength – Ball Burst Test |
| CAN 4.2 12.1 | Tearing Strength – Single-Rip Method |
| CAN 4.2 12.2 | Tearing Strength – Trapezoid Method |
| CAN 4.2 14 | Quantitative Analysis of Fibre Mixtures |
| CAN 4.2 15 | Non-fibrous Materials on Textiles |
| CAN 4.2 18.1 | Colourfastness to Artificial Light: Carbone-Arc Radiation |
| CAN 4.2 18.3 | Colourfastness to Artificial light: Xenon Arc Fading Lamp Test |
| CAN 4.2 19.1 | Colourfastness to Washing – Accelerated Test – Launder-Ometer |
| CAN 4.2 20 | Colourfastness to Water |
| CAN 4.2 21 | Colourfastness to Sea Water |
| CAN 4.2 22 | Colourfastness to Rubbing (Crocking) |
| CAN 4.2 23 | Colourfastness to Perspiration |
| CAN 4.2 24 | Colourfastness in Commercial Laundering |
| CAN 4.2 24.2 | Dimensional Change in Commercial Type Laundering of Textiles (Washwheel) |
| CAN 4.2 25.1 | Dimensional Change in Wetting |
| CAN 4.2 25.2 | Dimensional Change of Textile Fabrics to Open-Head Steaming |
| CAN 4.2 26.1 | Water Resistance — Static Head Penetration Test |
| CAN 4.2 26.2 | Determination of Resistance to Surface Wetting (Spray Test) |
| CAN 4.2 26.3 | Determination of Resistance to Water Penetration – Hydrostatic Pressure Test |
| CAN 4.2 26.3 | Resistance to Water Penetration – Sustained Pressure and Duration |
| CAN 4.2 26.5 | Water Resistance |
| CAN 4.2 27.1 | Flame Resistance – Vertical Burning Test |
| CAN 4.2 27.1 | Flame Resistance – Vertical Burning Test – After Commercial Laundering |
| CAN 4.2 27.10 | Flame Resistance — Vertically Oriented Test — Edge Ignition |
| CAN 4.2 27.2 | Flame Resistance – Surface Burning Test |
| CAN 4.2 27.3 | Measurement of flame spread properties of vertically oriented specimens (ISO 6941:2003, MOD) |
| CAN 4.2 27.4 | Burning behaviour — Determination of ease of ignition of vertically oriented specimens (ISO 6940:2004, MOD) |
| CAN 4.2 27.5 | Flame resistance – 45° angle test – One-second flame impingement |
| CAN 4.2 27.6 | Flame Resistance – Methenamine Tablet Test for Textile Floor Coverings |
| CAN 4.2 27.7 | Combustion Resistance of Mattresses – Cigarette Test |
| CAN 4.2 28.2 | Resistance to Micro-Organisms – Surface-Growing Fungus Test – Pure Culture |
| CAN 4.2 29.1 | Colourfastness to dry cleaning solvent |
| CAN 4.2 3 | Determination of Moisture in Textiles |
| CAN 4.2 30 | Dimensional Change in Dry Cleaning |
| CAN 4.2 31 | Colourfastness to Hot Pressing – Damp Pressing |
| CAN 4.2 32.1 | Resistance of Woven Fabrics to Seam Slippage |
| CAN 4.2 32.2 | Breaking Strength of Seams in Woven Fabrics |
| CAN 4.2 35.1 | Colourfastness to Burnt Gas Fumes |
| CAN 4.2 36 | Air Permeability |
| CAN 4.2 37 | Fabric Thickness |
| CAN 4.2 39 | Determination of Crimp of Yarn in Fabric |
| CAN 4.2 4.1 | Determination of Width |
| CAN 4.2 45 | Determination of the Recovery from Creasing by Measuring the Angle-of-Recovery |
| CAN 4.2 48 | Wool – Determination of Fibre Diameter – Projection Microscope Method (ISO 137:1975, MOD) |
| CAN 4.2 49 | Resistance of Materials to Water Vapour Diffusion |
| CAN 4.2 5.1 | Mass of fabrics |
| CAN 4.2 5.2 | Linear density of Yarn |
| CAN 4.2 51.1 | Resistance to Pilling, Rotating Box Method |
| CAN 4.2 51.2 | Resistance to Pilling – Random Tumble Pilling Tester |
| CAN 4.2 52.2 | Colourfastness to Chlorinated Water (Swimming-Pool Water) |
| CAN 4.2 57 | Determination of Maximum Safe Ironing Temperature |
| CAN 4.2 58 | Dimensional Change in Domestic Laundering of Textiles |
| CAN 4.2 6 | Construction of woven fabrics – Determination of number of threads per unit length |
| CAN 4.2 60 | Resistance to Snagging – Mace test |
| CAN 4.2 63.5 | Determination of Formaldehyde – Part 2: Released Formaldehyde (Vapour Absorption Method) |
| CAN 4.2 67 ASPECT | Appearance after Laundering of Coated, Bonded, Laminated and Fused Fabrics |
| CAN 4.2 67 STABILITÉ | Dimensional Change after Laundering of Coated, Bonded, Laminated and Fused Fabrics |
| CAN 4.2 7 | Knitted fabric count – Wales and courses per centimeter |
| CAN 4.2 74 | Determination of pH of aqueous extract |
| CAN 4.2 77.1 | Carpets – Determination of Tuft Withdrawal Force |
| CAN 4.2 78.1 | Thermal Protective Performance of Materials for Clothing |
| CAN 4.2 8.1 | Determination of Twist in Yarn Removed from Fabric |
| CAN 4.2 8.2 | Determination of Twist in Yarns – Direct Counting Method |
| CAN 4.2 9.1 | Breaking strength of fabrics – Strip Method |
| CAN 4.2 9.2 | Breaking strength of fabrics – Grab Method |
| CAN 4.2 9.3 | Breaking strength of high-strength fabrics — Constant-time-to-break principle |
| CAN 4.2 9.4 | Breaking strength of yarns – Single strand method |
| CAN 4.2 9.5 | Breaking strength of yarns – Skein method |
| CAN 51.33 GEN-REQ | General Requirements |
| CAN 51.33 PLIABILITY | Pliability |
| CAN 51.33 WVP | Water Vapour Permeance (ASTM E96/E96M) |
| CAN 75.1 SLIPRESIST | Slip Resistance Test |
| CAN 79.1 FLAME RESIS | Insect Screens – Flame Resistance (Fibreglass screening) |
| CAN 79.1 YARN SLIPPA | Insect Screens – Yarn Slippage Resistance (Fibreglass screening) |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Large-Flame Test – After dry cleaning |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Large-Flame Test |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Large-Flame Test – After laundering |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Large-Flame Test – After water leaching |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Large-Flame Test – After scrubbing |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Large-Flame Test – After weathering |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Small-Flame Test – After dry cleaning |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Small-Flame Test |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Small-Flame Test – After laundering |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Small-Flame Test – After water leaching |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Small-Flame Test – After scrubbing |
| CAN ULC S109 | Flame Tests of Flame-Resistant Fabrics and Films – Small-Flame Test – After weathering |
| CAN ULC S668 AGING | Soil Burial Test |
| CAN ULC S668 AGING | Accelerated Weathering Test |
| CAN ULC S668 AGING | Heat Aging Test |
| CAN ULC S668 BURST | Burst Strength Test |
| CAN ULC S668 CTCR | Cold Temperature Crack Resistance |
| CAN ULC S668 FLAM | Flammability test |
| CAN ULC S668 FLUID | Compatibility Test |
| CAN ULC S668 GRAB | Strength Test / Grab Test method |
| CAN ULC S668 SEAM | Seam Strength / Grab Test Method and Seam Peel Test |
| CAN ULC S668 TEAR | Tear Strength Test |
| CAN ULC S668 VAPOUR | Vapour Transmission Test |
| CAN ULC S702 MASS | Standard for Mineral Fiber Thermal Insulation for Buildings – Determination of Mass |
| CAN ULC S703 SORP | Standard for Cellulosic Fiber Thermal Insulation for Buildings – Water Vapor Sorption |
| CAN2 4.2 27.1 | Flame Resistance – Vertical Burning Test – After Commercial Laundering |
| CAN2 4.2 27.5 | Flame Resistance – 45° Angle Test |
| CAN2 4.2 27.5 | Flame Resistance – 45° Angle Test – After Commercial Laundering |
| CAN2 51.32 GEN-REQ | General Requirements |
| CAN2 51.32 TENSILE | Tensile Strength (ASTM D828-16e1) |
| CAN2 51.32 WIDTH | Sheet Width |
| CAN2 51.32 WVP | Water Vapour Permeance (ASTM E96/E96M-16) |
| CAN2 51.32 WVP | Water Vapour Permeance (ASTM E96/E96M-16) – After Accelerated Aging |
| CAN2 51.32PLIABILITY | Pliability |
| CAN3-A82.2 | Methods of Sampling and Testing Brick – Absorption |
| CCMC ASFT PEEL | Acrylic Seam and Flashing Tape – Peel Adhesion (ASTM D3330) After Shelf-Life Test |
| CCMC ASFT PEEL | Acrylic Seam and Flashing Tape – Peel Adhesion (ASTM D3330) After 25% Elongation |
| CCMC ASFT PEEL | Acrylic Seam and Flashing Tape – Peel Adhesion (ASTM D3330) |
| CCMC ASFT PEEL | Acrylic Seam and Flashing Tape – Peel Adhesion (ASTM D3330) at High Temperature |
| CCMC ASFT PEEL | Acrylic Seam and Flashing Tape – Peel Adhesion (ASTM D3330) at Low Temperature |
| CCMC ASFT SHEAR | Acrylic Seam and Flashing Tape – Shear Adhesion After 25% Elongation |
| CCMC ASFT SHEAR | Acrylic Seam and Flashing Tape – Shear Adhesion |
| CCMC ASFT SHEAR | Acrylic Seam and Flashing Tape – Shear Adhesion at High Temperature |
| CCMC ASFT SHEAR | Acrylic Seam and Flashing Tape – Shear Adhesion at Low Temperature |
| CCMC DM ALKALINE | Resistance to Alkaline Environment (EN 13967:2004 Mod.) |
| CCMC DM ALKALINE | Resistance to Alkaline Environment (EN 13967:2004 Mod.) |
| CCMC DM ANCHORAGE | Anchorage Performance |
| CCMC DM ANCHORAGE | Anchorage Performance |
| CCMC DM CELLCLASS | Identification of the Class (ASTM D3350) |
| CCMC DM CELLCLASS | Identification of the Class (ASTM D3350) |
| CCMC DM COLDBEND | Cold Bending (ASTM D2136 Mod.) |
| CCMC DM COLDBEND | Cold Bending (ASTM D2136 Mod.) after exposure to Alkaline Environment |
| CCMC DM COLDBEND | Cold Bending (ASTM D2136 Mod.) |
| CCMC DM COLDBEND | Cold Bending (ASTM D2136 Mod.) after exposure to Alkaline Environment |
| CCMC DM COMP-AGED | Compressive Strength (ASTM D6364 Mod.) after exposure to Alkaline Environment |
| CCMC DM COMP-AGED | Compressive Strength (ASTM D6364 Mod.) after Heat Aging |
| CCMC DM COMP-AGED | Compressive Strength (ASTM D6364 Mod.) after UV exposure |
| CCMC DM COMP-AGED | Compressive Strength (ASTM D6364 Mod.) after exposure to Alkaline Environment |
| CCMC DM COMP-AGED | Compressive Strength (ASTM D6364 Mod.) after Heat Aging |
| CCMC DM COMP-AGED | Compressive Strength (ASTM D6364 Mod.) after UV exposure |
| CCMC DM COMPRESSION | Compressive Strength (ASTM D6364 Mod.) |
| CCMC DM COMPRESSION | Compressive Strength (ASTM D6364 Mod.) |
| CCMC DM CREEP | Creep Resistance (ASTM D7361 Mod.) |
| CCMC DM CREEP | Creep Resistance (ASTM D7361 Mod.) – after Heat Aging |
| CCMC DM CREEP | Creep Resistance (ASTM D7361 Mod.) |
| CCMC DM CREEP | Creep Resistance (ASTM D7361 Mod.) – after Heat Aging |
| CCMC DM DYNIMPACT | Dynamic Impact Resistance (ASTM D5420 Mod.) |
| CCMC DM DYNIMPACT | Dynamic Impact Resistance (ASTM D5420 Mod.) |
| CCMC DM GEOMETRICAL | Geometrical Properties |
| CCMC DM GEOMETRICAL | Geometrical Properties |
| CCMC DM GTX-FOS | Geotextiles – Filtration Opening Size (CAN/CGSB 148.1 No.10) |
| CCMC DM GTX-GRAB | Grab Breaking Load and Elongation of Geotextiles (ASTM D4632) |
| CCMC DM GTX-PERM | Water Permeability of Geotextiles by Permittivity (ASTM D4491) |
| CCMC DM GTX-PUNCT | Index Puncture Resistance of Geomembranes and Related Products (ASTM D4833) |
| CCMC DM GTX-TEAR | Trapezoid Tearing Strength of Geotextiles (ASTM D4533) |
| CCMC DM GTX-UV | Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus (ASTM D4355) |
| CCMC DM HEATAGING | Heat Aging (ASTM D3045 Mod.) |
| CCMC DM HEATAGING | Heat Aging (ASTM D3045 Mod.) |
| CCMC DM ICF-COMP | Dimpled Sheet / ICF Compatibility |
| CCMC DM ICF-COMP | Dimpled Sheet / ICF Compatibility |
| CCMC DM LIGHT-TRANS | Light Transmission (ASTM E424) |
| CCMC DM LIGHT-TRANS | Light Transmission (ASTM E424) |
| CCMC DM OIT | Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry (ASTM D3895 Mod.) after Heat Aging |
| CCMC DM OIT | Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry (ASTM D3895 Mod.) after UV exposure |
| CCMC DM OIT | Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry (ASTM D3895 Mod.) after Heat Aging |
| CCMC DM OIT | Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry (ASTM D3895 Mod.) after UV exposure |
| CCMC DM TENSILE | Tensile Properties |
| CCMC DM TENSILE | Tensile Properties |
| CCMC DM TRANSMIS | Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head (ASTM D4716 Mod.) |
| CCMC DM UV | Resistance to Ultra-Violet Radiation (ASTM G155, cycle 3) |
| CCMC DM UV | Resistance to Ultra-Violet Radiation (ASTM G155, cycle 3) |
| CCMC ECS DIMENSIONAL | Dimensional Tolerance |
| CCMC ERM CHEM-EXP | Chemical exposure |
| CCMC ERM HEAT-AGING | Heat aging |
| CCMC PCP WATERPOND | Water Ponding Test |
| CCMC PCP WATERPOND | Water Ponding Test after Weathering |
| CCMC PVC-DM RE-STRUC | Reinforcement structure and material |
| CCMC TG 071123 15-D4 | Resistance to oxidation – carbonyl index |
| CFFA-100 | Accelerated Exposure To Disinfectants |
| CFFA-110 | Hydrolytic Stability – Polyurethane (exposure only) |
| CFFA-6 | Cold Crack Resistance |
| CGSB 20-GP-23M AGING | Cushion, Carpet, Flexible Polymeric Material: Deflection/Pressure Modulus, After Aging |
| CGSB 20-GP-23M COMP | Cushion, Carpet, Flexible Polymeric Material: Compression Set |
| CGSB 20-GP-23M DEFLE | Cushion, Carpet, Flexible Polymeric Material: Deflection/Pressure Modulus |
| CGSB 20-GP-23M THICK | Cushion, Carpet, Flexible Polymeric Material: Thickness |
| CGSB 37-GP-56M WATER | Membrane, Modified, Bituminous, Prefabricated, and Reinforced for Roofing – Watertightness Test |
| CIE 54.2 CERT | International Commission on Illumination – Retroreflection |
| COURTAULDS METHOD | Phenolic yellowing |
| CPAI 84 FLOORING | Flame Resistant Materials Used in Camping Tentage – Flooring Material |
| CPAI 84 FLOORING | Flame Resistant Materials Used in Camping Tentage – Flooring Material – After leaching |
| CPAI 84 FLOORING | Flame Resistant Materials Used in Camping Tentage – Flooring Material – After weathering |
| CPAI 84 WALL | Flame Resistant Materials Used in Camping Tentage – Wall and Top Material |
| CPAI 84 WALL | Flame Resistant Materials Used in Camping Tentage – Wall and Top Material – After leaching |
| CPAI 84 WALL | Flame Resistant Materials Used in Camping Tentage – Wall and Top Material – After weathering |
| CPSC-CH C1001 9.4 | Standard Operating Procedure for Determination of Phthalates |
| CPSC-CH E1002 8.3 | Standard Operating Procedure for Determining Total Lead (Pb) in Non-Metal Children’s Products |
| CPSC-CH E1003 9.1 | Standard Operating Procedure for Determining Lead (Pb) in Paint and Other Similar Surface Coatings (+CADMIUM) (Note 1) |
| CSA A220 AGING | Conditioning by Ultraviolet Exposure |
| CSA A220 AGING | Accelerated Aging |
| CSA A220 DIM-CHANGE | Linear Dimensional Changes |
| CSA A220 MASS | Mass per Unit Area |
| CSA A220 MVTR | Moisture Vapour Transmission Rate |
| CSA A220 PLIABILITY | Pliability |
| CSA A220 PUNCTURE | Puncture |
| CSA A220 RIGIDITY | Rigidity |
| CSA A220 ROLL-WIDTH | Roll Width |
| CSA A220 SAG | Long-Term Sag |
| CSA A220 TENSILE | Tensile Strength |
| CSA A220 WATER-PERM | Water Permeability |
| CSA B137.0 CBD | Thermoplastic pressure piping compendium – Definitions, general requirements, and methods of testing for thermoplastic pressure piping – Carbon |
| CSA B137.0 TENSILE | |
| Definitions, general requirements, and methods of testing for thermoplastic pressure piping – Apparent tensile properties (ring tensile test) | |
| CSA B181.0 WATER-RES | Definitions, general requirements, and methods of testing for thermoplastic nonpressure piping – Water resistance test |
| CSA B181.3 CHEM-RES | Polyolefin and polyvinylidene fluoride (PVDF) laboratory drainage systems – Chemical resistance |
| CSA Z195 SOLE PENETR | Protective sole penetration test |
| CTT PTC | Foot Thermal Rating Test (Dry) |
| DIN EN ISO 13938-2 | Bursting Strength |
| DIN EN ISO 62 | Plastics – Determination of water absorption |
| DORS 2016-169 ANN.1 | Flame Resistance Test — Loose fitting sleepwear – After 1 wash |
| DORS 2016-169 ANN.1 | Flame Resistance Test — Loose fitting sleepwear – After 20 washes |
| EN 1149-1 | Protective clothing – Electrostatic properties – Part 1: Test method for measurement of surface resistivity |
| EN 1149-2 | Test method for measurement of the electrical resistance through a material (vertical resistance) – After laundering |
| EN 12127 | Determination of mass per unit area using small samples |
| EN 12730 | Flexible sheets for waterproofing — Bitumen, plastic and rubber sheets for roof waterproofing — Determination of resistance to static |
| EN 13274-5 | |
| Respiratory protective devices – Methods of test – Part 5: Climatic conditions | EN 14362-1 |
| Determination of certain aromatic amines derived from azo colorants – Part 1: Detection of the use of certain azo colorants accessible with and without extracting the fibres | |
| EN 14414 | Screening test method for determining chemical resistance for landfill applications – Method D : Synthetic leachate |
| EN 14414 | Screening test method for determining chemical resistance for landfill applications – Method C |
| EN 14575 | Geosynthetic barriers – Screening test method for determining the resistance to oxidation |
| EN 14576 | Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking |
| EN 14683 ANNEX C | Determination of Breathability (Differential Pressure) |
| EN 16523-1 | Determination of material resistance to permeation by chemicals – Part 1: Permeation by liquid chemical under conditions of continuous |
| EN 1928 | Flexible sheets for waterproofing – Bitumen, plastic and rubber sheets for waterproofing – Determination of watertightness |
| EN 20811 | Determination of resistance to water penetration — Hydrostatic pressure test – After laundering |
| EN 342 INSPECTION | Visual Inspection |
| EN 343 DIMENS CHANGE | Dimensional change – After laundering |
| EN 343 WATER PEN | Resistance to water penetration |
| EN 343 WATER VAPOUR | Water vapour resistance |
| EN 388 ABRASION | Abrasion Resistance |
| EN 388 BLADE CUT | Blade Cut Resistance |
| EN 388 CUT RESIST | Cut Resistance (EN ISO 13997) |
| EN 388 PUNCTURE | Puncture Resistance |
| EN 388 TEAR | Tearing Resistance |
| EN 530 | Abrasion resistance of protective clothing material — Test method 2 |
| EN 61386-1 CRUSH | Conduit systems for cable management – Part 1: General requirements – Crush resistance |
| EN 863 | Protective clothing – Mechanical properties – Test method: Puncture resistance |
| EN ISO 9237 | Determination of the permeability of fabrics to air |
| EPA 6010D | Inductively Coupled Plasma — Optical Emission Spectrometry |
| FAR 25.853 F PAR.4 | Paragraph 4: Vertical test – 12 seconds |
| FAR 25.853 F PAR.4 | Paragraph 4: Vertical test – 60 seconds |
| FAR 25.853 F PAR.5 | Paragraph 5: Horizontal test |
| FAR 25.853 F PAR.6 | Paragraph 6: Forty-five degree test |
| FAR 25.853 F PAR.7 | Paragraph 7: Sixty degree test |
| GARMENT DESIGN | Design |
| GARMENT DESIGN | Garment Class, Level, and Design |
| GCTTG 145 | Dyeing of a textile swatch |
| GCTTG 147 | Particle size distribution – Zetasizer |
| GCTTG 153 | Simulation of Gas penetration test with liquid simulant |
| GCTTG 154 | Test Method for Filtration of 0.3 micron NaCl particles by Materials Used in Medical Face Masks |
| GCTTG 157 | Filtration Efficiency Test |
| GCTTG 158 | Test Method for In-Situ Measurement of Floor Temperature |
| GCTTG 159 | Colorfastness to Autoclave |
| GCTTG 160 | Freeze/Thaw cycling |
| GCTTG 161 | Thermal resistance in steady state under extreme cold conditions |
| GCTTG 162 | Compressed volume of sleeping bag samples |
| GCTTG 163 | Packing Volume |
| GCTTG 166 | Yarn Analysis – Determination of yarn construction |
| GCTTG 4005 | Thermal Conductivity and Effusivity Test for Textile Materials |
| GLPD-12-16 COMPR VOL | Compressed volume |
| GLPD-12-16 STATIC | Electrostatic decay |
| GMW 3232 | Test Method for Determining the Flammability of Interior Trim Materials |
| GRI GM11 | Accelerated Weathering of Geomembranes using a Fluorescent UVA-Condensation Exposure Device |
| GRI GM12 | Asperity Measurement of Textured Geomembranes Using a Depth Gage |
| GRI GS13 | Geom. Related Geocell Seam Strength and Its Efficiency with Respect to the Perforated Shear Strength |
| GRI GS14 | Average Wall Thickness of a Geomembrane-Related Geocell by Indirect Measurement |
| GRI-GG2 | Individual Geogrid Junction Strength |
| ICC ES AC114 AGING | Chemical Exposure – Ammonium Chloride |
| ICC ES AC114 AGING | Chemical Exposure – Sodium Sulfate |
| ICC ES AC114 AGING | Water immersion |
| ICC ES AC114 AGING | Heat Aging |
| ICC ES AC114 COMP | Compression Test |
| ICC ES AC114 IMPACT | Dynamic Impact Test |
| ICC ES AC114 LT-FLEX | Low-temperature Flexibility |
| ICC ES AC114 PUNCT | Static Puncture |
| ICC ES AC114 TENSILE | Tensile Strength and Elongation |
| ICC ES AC114 TENSILE | Tensile Strength and Elongation – After Chemical Exposure to Ammonium Chloride |
| ICC ES AC114 TENSILE | Tensile Strength and Elongation – After Heat Aging |
| ICC ES AC114 TENSILE | Tensile Strength and Elongation – After Chemical Exposure to Sodium Sulfate |
| ICC ES AC114 TENSILE | Tensile Strength and Elongation – After Water Immersion |
| ICC ES AC114 T-W | Thickness and Weight |
| ICC ES AC114 WVP | Water Vapour Permeability |
| ICC-ES AC207 AGING | Accelerated Aging |
| ICC-ES AC207 PLIAB | Pliability |
| ICC-ES AC207 UV | Ultraviolet Exposure |
| ICC-ES AC38 COLDBEND | Acceptance Criteria for Water-Resistive Barriers – Cold Bending |
| ICC-ES AC38 WATERPON | Acceptance Criteria for Water-Resistive Barriers – Water Ponding Test |
| ICC-ES AC38 WATERPON | Acceptance Criteria for Water-Resistive Barriers – Water Ponding Test after Weathering |
| ICC-ES AC48 ACCAGING | Accelerated Aging |
| ICC-ES AC48 ACCAGING | Requirements for Water Resistive Barriers – Accelerated Aging |
| ICC-ES AC48 ACCAGING | Acceptance Criteria for Water-Resistive Barriers – Accelerated Aging |
| ICC-ES AC48 CYCLING | Cycling and Elongation Test |
| ICC-ES AC48 PEEL | Peel Adhesion Test |
| ICC-ES AC48 PEEL | Peel Adhesion Test – After accelerated aging |
| ICC-ES AC48 PEEL | Peel Adhesion Test – After UV exposure |
| ICC-ES AC48 PEEL | Peel Adhesion Test – After water immersion |
| ICC-ES AC48 PLIABILI | Pliability |
| ICC-ES AC48 TENSILE | Tensile Strength Tests |
| ICC-ES AC48 TENSILE | Tensile Strength Tests after Accelerated Aging |
| ICC-ES AC48 TENSILE | Tensile Strength Tests after UV Exposure |
| ICC-ES AC48 UV | Ultraviolet Exposure |
| ICC-ES AC48 UV | Acceptance Criteria for Water-Resistive Barriers – Ultraviolet Light Exposure |
| ICC-ES AC48 WATERPON | Water-ponding Test |
| ICC-ES AC48 WATERPON | Water-ponding Test – After accelerated aging |
| ICC-ES AC48 WVT | Water Vapor Transmission of Materials |
| IEEE C37.20.2 FLAME | Flammability -Applied insulation |
| INDA IST 10.1 ABS CA | Absorptive Capacity Test (for small specimens) |
| INDA IST 10.1 ABSORB | Absorbency Time Test |
| INDA IST 10.1 WICK | Wicking Rate |
| IPC TM 650 2.4.8 | Peel Strength of Metallic Clad Laminates |
| ISO 10319 | Wide-width Tensile Test |
| ISO 105 B02 | Colour fastness to artificial light: Xenon arc fading lamp test – Cycle A1 |
| ISO 105 B02 | Colour fastness to artificial light: Xenon arc fading lamp test – Cycle A2 |
| ISO 105 B02 | Colour fastness to artificial light: Xenon arc fading lamp test – Cycle B |
| ISO 105-C06 | Colour fastness to domestic and commercial laundering |
| ISO 105-C12 | Colour fastness to industrial laundering |
| ISO 105-D01 | Colour fastness to dry cleaning using perchloroethylene solvent |
| ISO 105-E01 | Colour fastness to water |
| ISO 105-E02 | Colour fastness to sea water |
| ISO 105-E03 | Colour fastness to chlorinated water (swimming-pool water) |
| ISO 105-E04 | Colour fastness to perspiration |
| ISO 105-N01 | Colour fastness to bleaching: Hypochlorite |
| ISO 105-X05 | Colour fastness to organic solvents |
| ISO 105-X11 | Colourfastness to Hot Pressing – Dry Pressing |
| ISO 105-X11 | Colourfastness to Hot Pressing – Wet Pressing |
| ISO 105-X11 | Colourfastness to Hot Pressing – Damp Pressing |
| ISO 105-X12 | Colour fastness to rubbing |
| ISO 105-X18 | Assessment of the potential to phenolic yellowing of materials |
| ISO 10618 | Carbon fibre — Determination of tensile properties of resin-impregnated yarn |
| ISO 11058 | Determination of water permeability characteristics normal to the plane, without load |
| ISO 11092 | Water-Vapour Resistance Under Steady-State Conditions (Sweating Guarded-Hotplate Test) |
| ISO 11092 | Thermal Resistance Under Steady-State Conditions (Sweating Guarded-Hotplate Test) |
| ISO 11092 | Thermal Resistance Under Steady-State Conditions (Sweating Guarded-Hotplate Test) – After laundering |
| ISO 1133 | Plastics – Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics – Part 1: Standard method |
| ISO 11357-6 | Plastics – Determination of oxidation induction time (isothermal OIT) |
| ISO 11359-2 | Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 11611 DESIGN | General and Design requirements |
| ISO 1172 | Determination of the textile-glass and mineral-filler content – Calcination methods |
| ISO 1183-1 | Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method |
| ISO 1183-2 | Determining the density of non-cellular plastics – Part 2: Density gradient column method |
| ISO 12127-1 | Determination of contact heat transmission through protective clothing or constituent materials – Part 1: Contact heat produced by heating cylinder (Code letter F) – After laundering |
| ISO 12236 | Static puncture test (CBR test) |
| ISO 12945 | Determination of fabric propensity to surface fuzzing and to pilling – Part 1: Pilling box method |
| ISO 12945 | Determination of propensity to surface fuzzing and to pilling – Part 2: Modified Martindale method |
| ISO 12947-2 | Abrasion resistance of fabrics by the Martindale method – Part 2: Determination of specimen breakdown |
| ISO 12956 | Determination of the characteristic opening size |
| ISO 12958-1 | Determination of water flow capacity in their plane – Part 1 : Index test |
| ISO 12958-2 | Determination of water flow capacity in their plane – Part 2 : Performance test |
| ISO 13426-1 | Geotextiles and Geotextile-Related Products – Strength of Internal Structural Junctions – Part 1: Geocells |
| ISO 13433 | Dynamic perforation test (cone drop test) |
| ISO 13438 | Geotextiles and geot.-related products-Screening test method for determining resistance to oxidation |
| ISO 13506-1 | Protective clothing against heat and flame — Part 1: Test method for complete garments – Measurement of transferred energy using an instrumented manikin – After washing and drying (1 cycle) |
| ISO 137 | Wool – Determination of Fibre Diameter – Projection Microscope Method |
| ISO 13934-1 | Determination of maximum force and elongation at maximum force using the strip method – After laundering |
| ISO 13934-2 | Tensile properties of fabrics – Part 2: Determination of maximum force using the grab method |
| ISO 13935-2 | Seam tensile properties of fabrics and made-up textile articles – Part 2: Determination of maximum force to seam rupture using the grab method |
| ISO 13937-2 | Tear properties of fabrics — Part 2: Tear force of trouser-shaped test specimens (Single tear) |
| ISO 13937-3 | Tear properties of fabrics – Part 3: Determination of tear force of wing-shaped test specimens (Single tear method) |
| ISO 13938-1 | Textiles – Bursting properties of fabrics – Part 1: Hydraulic method for determination of bursting strength and bursting distension |
| ISO 13953 | Determination of the tensile strength and failure mode of test pieces from butt-fused joint |
| ISO 13996 | Protective clothing – Mechanical properties – Determination of resistance to puncture |
| ISO 13997 | Determination of resistance to cutting by sharp objects |
| ISO 14125 | Fibre-reinforced plastic composites — Determination of flexural properties |
| ISO 14184-1 | Determination of formaldehyde — Part 1: Free and hydrolized formaldehyde (water extraction method) |
| ISO 1419 | Rubber- or plastics-coated fabrics — Accelerated-ageing tests |
| ISO 1421 1 STRIP | Determination of Tensile Strength and Elongation at Break – Method 1: Strip Method |
| ISO 1421 2 GRAB TEST | Determination of Tensile Strength and Elongation at Break – Method 2: Grab test |
| ISO 14419 | Oil repellency — Hydrocarbon resistance test |
| ISO 15025 | Protective clothing – Protection against flame – Method of test for limited flame spread – Procedure B |
| ISO 15025 | Protective clothing – Protection against heat and flame – Method of test for limited flame spread – Procedure A |
| ISO 15148 | Hygrothermal performance of building materials and products – Determination of water absorption coefficient by partial immersion |
| ISO 16322-2 | Determination of spirality after laundering – Part 2: Woven and knitted fabrics |
| ISO 16373-1 | Textiles – Dyestuffs – Part 1: General principles of testing coloured textiles for dyestuff identification |
| ISO 17072-1 | Leather – Chemical determination of metal content – Part 1: Extractable metals |
| ISO 17072-2 | Leather – Chemical determination of metal content – Part 2: Total metal content |
| ISO 17103 PERF | Agricultural machinery — Rotary disc mowers, rotary drum mowers and flail mowers — Test methods and acceptance criteria for protective skirts — Resistance to perforation test |
| ISO 17131 | Leather – Identification of leather with microscopy |
| ISO 17230 | Leather – Physical and mechanical tests – Determination of water penetration pressure |
| ISO 17353 | Water quality – Determination of selected organotin compounds – Gas chromatographic method |
| ISO 17492 | Determination of heat transmission on exposure to both flame and radiant heat |
| ISO 17492 | Clothing for protection against heat and flame – Determination of heat transmission on exposure to both flame and radiant heat |
| ISO 17493 | Convective heat resistance using a hot air circulating oven |
| ISO 18325 | Geosynthetics – Test method for the determination of water discharge capacity for prefabricated vertical drains |
| ISO 1833-11 | Textiles – Quantitative chemical analysis – Part 11: Mixtures of certain cellulose fibres with certain other fibres (method using sulfuric acid) |
| ISO 18488 | Polyethylene (PE) materials for piping systems — Determination of Strain Hardening Modulus in relation to slow crack growth |
| ISO 20344 5.13 COLD | Determination of insulation against cold |
| ISO 20344 5.2 BOND | Personal protective equipment – Test methods for footwear – Determination of upper/outsole and sole interlayer bond strength |
| ISO 20344 6.12 ABRAS | Determination of abrasion resistance of lining and insock |
| ISO 20344 6.4.2BREAK | Determination of the breaking force of a rubber boot upper |
| ISO 20344 8.6 OIL | Personal protective equipment – Test methods for footwear – Determination of resistance to fuel oil |
| ISO 20471 COLOUR | Determination of colour |
| ISO 20471 COLOUR | Determination of colour – After xenon test |
| ISO 20471 REFLECTION | Photometric Performance Requirements After Test Exposure – Rainfall |
| ISO 2062 | Textiles — Yarns from packages — Determination of single-end breaking force and elongation at break using constant rate of extension (CRE) tester |
| ISO 20743 | Determination of antibacterial activity of textile products |
| ISO 20743 | Determination of antibacterial activity of textile products |
| ISO 22196 | Measurement of antibacterial activity on plastics and other non-porous surfaces |
| ISO 22609 | Clothing for protection against infectious agents – Medical face masks – Test method for resistance against penetration by synthetic blood (fixed volume, horizontally projected) |
| ISO 22612 | Clothing for protection against infectious agents – Test method for resistance to dry microbial penetration |
| ISO 2286-2 | Rubber- or plastics-coated fabrics – Determination of roll characteristics Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate |
| ISO 2307 | Fibre ropes – Determination of certain physical and mechanical properties |
| ISO 25619-2 | Determination of compression behaviour-Part 2: Determination of short-term compression behaviour |
| ISO 2813 | Paints and varnishes – Determination of specular gloss of non-metallic paint films |
| ISO 3146 | Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| ISO 3175-2 | Textiles – Dry cleaning and finishing – Part 2: Procedures for tetrachloroethene |
| ISO 34 | Rubber, vulcanized or thermoplastic – Determination of tear strength (Part 1) |
| ISO 3801 | Determination of mass per unit length and mass per unit area |
| ISO 4045 | Leather – Chemical tests – Determination of pH and difference figure |
| ISO 4674-1 | Determination of tear resistance – Part 1: Constant rate of tear methods |
| ISO 4674-2 | Rubber- or plastics-coated fabrics – Determination of tear resistance – Part 2: Ballistic pendulum method |
| ISO 4675 | Rubber- or plastics-coated fabrics – Low-temperature bend test |
| ISO 4892-2 | Plastics – Methods of exposure to laboratory light sources – Part 2: Xenon-arc lamps – Amendment 1: Classification of daylight filters » |
| ISO 4892-3 | « Plastics – Methods of exposure to laboratory light sources – Part 3: Fluorescent UV lamps » |
| ISO 4918 | Resilient, textile and laminate floor coverings — Castor chair test |
| ISO 4920 | Determination of Resistance to Surface Wetting (Spray Test) |
| ISO 5077 | Determination of dimensional change in washing and drying |
| ISO 5079 | Textile fibres – Determination of breaking force and elongation at break of individual fibres |
| ISO 5084 | Determination of thickness of textiles and textile products |
| ISO 527-2 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 527-3 | Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets |
| ISO 527-4 | Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| ISO 536 | Paper and board – Determination of grammage |
| ISO 5470-2 | Rubber- or plastics-coated fabrics – Determination of abrasion resistance – Part 2: Martindale abrader |
| ISO 6330 | Domestic washing and drying procedures for textile testing |
| ISO 6530 | « Protective clothing – Protection against liquid chemicals – Test method for resistance of materials to penetration by liquids » |
| ISO 6721-4 | Plastics — Determination of dynamic mechanical properties — Part 4: Tensile vibration — Non-resonance method |
| ISO 6721-5 | Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method |
| ISO 675 | Determination of dimensional change on commercial laundering near the boiling point |
| ISO 6940 | Burning behaviour — Determination of ease of ignition of vertically oriented specimens |
| ISO 6942 | Evaluation of materials and material assemblies when exposed to a source of radiant heat – Method B |
| ISO 6964 | Polyolefin pipes and fittings – Determination of carbon black content by calcination and pyrolysis |
| ISO 7198 WATER PERM | Determination of water permeability |
| ISO 7211-5 | Construction – Methods of analysis – Part 5: Determination of linear density of yarn removed from fabric |
| ISO 7393-2 | Water quality – Determination of free chlorine and total chlorine – Part 2 : Colorimetric method using N,N-diethyl-1,4-phenylenediamine, for routine control purposes |
| ISO 7724-2 | « Paints and varnishes – Colorimetry – Part 2 : Colour measurement » |
| ISO 7854 | « Determination of resistance to damage by flexing – Method A: De Mattia method » |
| ISO 7854 | « Determination of resistance to damage by flexing – Method C: Crumple/Flex method » |
| ISO 811 | « Determination of resistance to water penetration – Hydrostatic pressure test » |
| ISO 811 | Determination of resistance to water penetration — Hydrostatic pressure test – After chemicals |
| ISO 846 | « Plastics – Evaluation of the action of microorganisms – Method C: Resistance to bacteria » |
| ISO 868 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ISO 9073-1 | « Textiles – Test methods for nonwovens – Part 1: Determination of mass per unit area » |
| ISO 9073-10 | Textiles – Test methods for nonwovens – Part 10: Lint and other particles generation in the dry state |
| ISO 9073-2 | « Textiles – Test methods for nonwovens – Part 2: Determination of thickness » |
| ISO 9073-3 | « Textiles – Test methods for nonwovens – Part 3: Determination of tensile strength and elongation » |
| ISO 9073-4 | Nonwovens – Test methods – Part 4: Determination of tear resistance by the trapezoid procedure |
| ISO 9073-5 | « Textiles – Test methods for nonwovens – Part 5: Determination of resistance to mechanical penetration (ball burst procedure) » |
| ISO 9073-6 | « Test methods for nonwovens – Part 6: Absorption Method: Liquid wicking rate » |
| ISO 9150 | Protective clothing – Determination of behaviour of materials on impact of small splashes of molten metal |
| ISO 9151 | Determination of heat transmission on exposure to flame – After laundering |
| ISO 9185 | « Assessment of resistance of materials to molten metal splash – Molten aluminium splash (code letter D) – After laundering » |
| ISO 9185 | « Assessment of resistance of materials to molten metal splash – Molten iron splash (code letter E) – After laundering » |
| ISO 9237 | Determination of the permeability of fabrics to air |
| ISO 9863-1 | Determination of the thickness at prescribed pressure |
| ISO 9864 | Determination of Mass per Unit Area |
| ISO 9867 | Evaluation of the wrinkle recovery of fabrics — Appearance method |
| JIS L 1041 | Determination of Free Formaldehyde – Liquid Extraction Method – Acetylacetone Method B |
| JIS L 1092 | Water resistance of textiles – Water penetration test (Hydrostatic pressure method) – Method A |
| JIS L 1092 | Water resistance of textiles – Water penetration test (Hydrostatic pressure method) – Method B |
| MA.100-S.T.1.1 ASH | « Détermination des solides totaux et des solides totaux volatils : méthode gravimétrique » |
| MA.200-MET.1.2 | Metal analysis – Method by Mass Spectrometry – Inductively Coupled Plasma |
| MA.200-MET.1.2 | Standard Operating Procedure for Determining Silver |
| MA.200-MET.1.2 | Metal analysis – Method by Mass Spectrometry – Inductively Coupled Plasma |
| MIL-STD-810H FUNGUS | Fungus |
| NEAR INFRARED | Near Infrared Reflectance |
| NEMA LD3 LIGHT | Light Resistance |
| NEN-EN 13087-7 | Protective helmets – Test methods – Part 7: Flame resistance |
| NF EN 1049-2 | « Woven fabrics – Construction – Methods of analysis – Part 2: Determination of number of threads per unit length » |
| NF EN 12224 | Geotextiles and geotextile-related products – Determination of the resistance to weathering |
| NF EN 12311-1 | Flexible sheets for waterproofing – Determination of tensile properties – Part 1: Bitumen sheets for roof waterproofing |
| NF EN 12311-2 | Flexible sheets for waterproofing – Determination of tensile properties – Part 2: Plastic and rubber sheets for roof waterproofing |
| NF EN 13832-1 | « Footwear protecting against chemicals – Part 1: Terminology and test methods – Section 4.2: Splashing test » |
| NF EN 14151 | Determination of burst strength |
| NF EN 15237 | Execution of special geotechnical work — Vertical drainage – Discharge capacity |
| NF EN 1849-2 | Flexible sheets for waterproofing – Determination of mass per unit area |
| NF EN 420 DIMENSION | Hand and glove measurement and dimensions |
| NF EN 420 FINGER DEX | Protective gloves – Gloved Finger Dexterity |
| NF EN 863 | Puncture resistance |
| NF EN 964-1 | Determination of thickness at specified pressures |
| NF EN 965 | Determination of mass per unit area |
| NF F31-250 HUMIDITE | « Matériel roulant ferroviaire — Verres feuilletés – Tenue à l’humidité » |
| NF F31-250 SOLAIRE | « Matériel roulant ferroviaire — Verres feuilletés – Tenue au rayonnement solaire » |
| NF F31-250 TEMP | « Matériel roulant ferroviaire — Verres feuilletés – Tenue à la température » |
| NF G 07 166 | Determination of water retention rate and drying duration |
| NF G 38-016 | Measurement of water permeability |
| NF G 38-017 | Measurement of pore size – Determination of filtration opening |
| NF G 38-018 | Measurement of the water transmissivity |
| NF G 38-019 | Determination of resistance to stamping |
| NF ISO 17617 | Textiles — Determination of moisture drying rate |
| NF P 84-507 | Static puncture resistance of geomembranes and geomembrane lining systems |
| NFPA 1951 ABRASION-1 | Abrasion Resistance Test 1 |
| NFPA 1951 CLEAN SHRI | Cleaning Shrinkage Resistance Test |
| NFPA 1951 HTS | Heat and Thermal Shrinkage Resistance Test |
| NFPA 1951 LABELS | Label Durability and Legibility Test |
| NFPA 1951 THREAD | Thread Heat Resistance Test |
| NFPA 1951 WATER ABS | Water Absorption Resistance |
| NFPA 1951 WOVEN SEAM | Seam Breaking Strength |
| NFPA 1971 BURST DYN | Burst Strength Test |
| NFPA 1971 CLEAN SHRI | Cleaning Shrinkage Resistance Test |
| NFPA 1971 FLAM TEST1 | Flame Resistance Test 1 |
| NFPA 1971 FLUORESCEN | Evaluation of Fluorescence |
| NFPA 1971 HTS | Heat and Thermal Shrinkage Resistance Test |
| NFPA 1971 LIGHT DEGR | Light Degradation Resistance Test – After conditioning |
| NFPA 1971 LIQ INTEG1 | Overall Liquid Integrity Test 1 |
| NFPA 1971 LIQUID PEN | Liquid Penetration Resistance Test – After conditioning |
| NFPA 1971 PBT | Particulate Blocking Test |
| NFPA 1971 PRE-COND | Pre-Conditioning |
| NFPA 1971 REFLECTION | Measurement of Coefficient of Retroreflection – Convective Heat Exposure Test |
| NFPA 1971 REFLECTION | Measurement of Coefficient of Retroreflection – Rainfall Test |
| NFPA 1971 REFLECTION | Measurement of Coefficient of Retroreflection |
| NFPA 1971 TEAR | Tear Resistance Test |
| NFPA 1971 THL | Total Heat Loss (THL) Test |
| NFPA 1971 THREAD | Thread Melting Test |
| NFPA 1971 TPP | Thermal Protective Performance (TPP) Test |
| NFPA 1971 TPP | Thermal Protective Performance (TPP) Test – After washing and drying |
| NFPA 1971 WATER PEN | Water Penetration Resistance Test |
| NFPA 1971 WATER PEN | Water Penetration Resistance Test – After conditioning |
| NFPA 1975 FLAME TEST | Flame Resistance Test – After laundering |
| NFPA 1975 HTS | Heat and Thermal Shrinkage Resistance |
| NFPA 1975 HTS | Heat and Thermal Shrinkage Resistance – After drycleaning |
| NFPA 1975 HTS | Heat and Thermal Shrinkage Resistance – After laundering |
| NFPA 1975 THER STAB | Thermal Stability Test – After laundering |
| NFPA 1975 THREAD | Thread Heat Resistance Test |
| NFPA 1977 BURST | Burst Strength Test |
| NFPA 1977 CLEAN SHRI | Cleaning Shrinkage Resistance Test |
| NFPA 1977 FLAME TEST | Flame Resistance Test |
| NFPA 1977 FLAME TEST | Flame Resistance Test – After laundering |
| NFPA 1977 HTS | Heat and Thermal Shrinkage Resistance Test |
| NFPA 1977 HTS | Heat and Thermal Shrinkage Resistance Test – After laundering |
| NFPA 1977 REFLECTION | Retroreflectivity Test – After Convective Heat Exposure |
| NFPA 1977 REFLECTION | Retroreflectivity Test – Under Rainfall |
| NFPA 1977 REFLECTION | Retroreflectivity Test |
| NFPA 1977 RPP | Radiant Protective Performance (RPP) Test |
| NFPA 1977 RPP | Radiant Protective Performance (RPP) Test – After laundering |
| NFPA 1977 TEAR | Tear Resistance Test |
| NFPA 1977 THL | Total Heat Loss Test – After laundering |
| NFPA 1977 THREAD | Thread Melting Test |
| NFPA 1992 BURST DYN | Burst Strength Test |
| NFPA 1992 COLD TEST1 | Cold Temperature Performance Test 1 |
| NFPA 1992 LIQUID PEN | Chemical Penetration Resistance Test – After conditioning |
| NFPA 1992 TEAR | Puncture Propagation Tear Resistance Test |
| NFPA 1994 CHEM PERM | Chemical Permeation Resistance Test |
| NFPA 1999 RET | Evaporative Resistance Test |
| NFPA 1999 WATER ABS | Water Absorption Resistance |
| NFPA 1999 WVT PROC.B | Moisture Vapor Transmission Rate Test |
| NFPA 2112 FLAME TEST | Flame Resistance Test |
| NFPA 2112 FLAME TEST | Protective Glove Flame Resistance Test |
| NFPA 2112 FLAME TEST | Protective Glove Flame Resistance Test – After dry cleaning (3 cycles) |
| NFPA 2112 FLAME TEST | Protective Glove Flame Resistance Test- After washing & drying (3 cycles) |
| NFPA 2112 HTP | Heat Transfer Performance (HTP) Test — Contact Test |
| NFPA 2112 HTP | Heat Transfer Performance (HTP) Test — Contact Test – After washing & drying (3 cycles) |
| NFPA 2112 HTP | Heat Transfer Performance (HTP) Test — Spaced Test |
| NFPA 2112 HTP | Heat Transfer Performance (HTP) Test — Spaced Test – After washing & drying (3 cycles) |
| NFPA 2112 HTS | Heat and Thermal Shrinkage Resistance Test |
| NFPA 2112 HTS | Heat and Thermal Shrinkage Resistance Test – After washing & drying (3 cycles) |
| NFPA 2112 HTS | Heat and Thermal Shrinkage Resistance Test |
| NFPA 2112 HTS | Heat Resistance Test |
| NFPA 2112 HTS | Heat Resistance Test – After dry cleaning (3 cycles) |
| NFPA 2112 HTS | Heat Resistance Test – After washing & drying (3 cycles) |
| NFPA 2112 HTS | Heat and Thermal Shrinkage Resistance Test – After dry cleaning (3 cycles) |
| NFPA 2112 LABELS | Label Print Durability – After drycleaning (3 cycles) |
| NFPA 2112 LABELS | Label Print Durability – After washing & drying (3 cycles) |
| NFPA 2112 MANIKIN | Manikin Test – After dry cleaning (1 cycle) |
| NFPA 2112 MANIKIN | Manikin Test – After washing and drying (1 cycle) |
| NFPA 2112 THREAD | Thread Heat Resistance Test |
| NFPA 253 | Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source |
| NFPA 260 COVER TEST | Cigarette Ignition Resistance of Components of Upholstered Furniture – Cover Fabric Test |
| NFPA 701 TEST 1 | Fire Tests for Flame Propagation of Textiles and Films – Test method 1 – After laundering |
| NFPA 701 TEST 1 | Fire Tests for Flame Propagation of Textiles and Films – Test method 1 – After Water Leaching |
| NFPA 701 TEST 1 | Fire Tests for Flame Propagation of Textiles and Films – Test method 1 – After Dry Cleaning |
| NFPA 701 TEST 1 | Fire Tests for Flame Propagation of Textiles and Films – Test method 1 |
| NFPA 701 TEST 2 | Fire Tests for Flame Propagation of Textiles and Films – Test Method 2 – After laundering |
| NFPA 701 TEST 2 | Fire Tests for Flame Propagation of Textiles and Films – Test Method 2 – After Water Leaching |
| NFPA 701 TEST 2 | Fire Tests for Flame Propagation of Textiles and Films – Test Method 2 – After Dry Cleaning |
| NFPA 701 TEST 2 | Fire Tests for Flame Propagation of Textiles and Films – Test Method 2 |
| NIJ 0117.01 FLAME | Flammability Test for Helmets |
| OIL RESISTANCE | Resistance to organic liquid – Initial |
| PSTC 101 | Peel Adhesion of Pressure Sensitive Tapes |
| PSTC 107 | Shear Adhesion of Pressure Sensitive Tape |
| PSTC 5 | Quick Stick of Pressure Sensitive Tapes |
| SAGEOS GD001 | Stress-Cracking Resistance of Dimpled Sheets using the « Sweden Test » |
| SAGEOS GX 010 | Water Holding Capacity |
| SAGEOS GX 012 | Capillary Rise on an Inclined Plane |
| SAGEOS GX 013 | Water Front Speed in Capillary Mats |
| SAGEOS SIP031-1 | Split Drum / Incline Plane Static Friction |
| SANTÉCANADA B C02 | Determination of total lead in paints and applied coatings |
| SANTÉCANADA B C02.4 | Determination of total lead in metallic consumer products |
| SMP 800-C | Toxic Gas Generation from Material Combustion |
| SRM 1R | SACMA Recommended Test Method for Compressive Properties of Oriented Fiber-Resin Composites |
| TAPPI T461 | Flame resistance of treated paper and paperboard |
| TAPPI T476 | Abrasion loss of paper and paperboard (Taber-type method) |
| TAPPI T825 | Flat crush test of corrugated board (rigid support method) |
| TAPPI T839 | Edgewise compressive strength of corrugated fiberboard using the clamp method (short column test) |
| TAS 117B | Test Procedure for Dynamic Pull-Through Performance of Roofing Membrane over Fastener Heads or Fasteners with Metal Bearing Plates |
| TM 31 | Woolmark Test Method: Washing of Wool Textile Products |
| TP 1324 PAR 4.5 | Puncture Resistance |
| TTM 074 | Fabric Elongation (Hanging Weight Test) |
| TTM 077 | Fabric Growth |
| UFAC COVER TEST | Fabric Classification Test Method |
| UL 2515 PAR 5.10 | Aboveground Reinforced Thermosetting Resin Conduit (RTRC) and Fittings – Flame retardant properties |
| UL 94 PAR 7 HB | Flammability of plastic materials for parts in devices and appliances – Horizontal Burning Test |
| UL 94 PAR 8 VB | 50W (20 mm) Vertical Burning Test; V-0, V-1, or V-2 |
| UL 94 PAR 8 VB | 50W (20 mm) Vertical Burning Test; V-0, V-1, or V-2 – Heat conditioned |
ACCRÉDITATIONS
